VESPA LX 50 Скачать руководство пользователя страница 97

Страница: 97 / 160

- Lubricate the sealing rings with mineral oil and

half-fill the roller casings with grease.

- Insert the sealing ring on the pin and the roller

bushing with wedging washers at the same time.

- Remove the specific tool, then the part 5 (guiding)

partially ejected in the previous assembly stage;

leave part 4* always fitted.

- Replace part 3 with part 16* on the stem.

- Push, from the handgrip, the wedging washer -

roller casing - sealing ring unit, placing part 16 until

it stops on the swinging hub

- Repeat the operation described above using the

tool fitted with part 16 and part 22* instead of part

4 on the stem, on the side opposite the one shown

in the figure to refit the second wedging washer -

roller casing - sealing ring unit.

* Supplied with the tool

Specific tooling

020021Y

Front suspension service tool

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

Use the tool fitted with parts 3 and 4, as indicated

to fit the pin, and press operating the handgrip,

until wedging the washers on the swinging hub.

- Remove the spacers, part 17, fill with grease the

area between the steering tube and the swinging

hub, and place the dust guard rings in that place.

* Supplied with the tool

N.B.

ASSEMBLE THE LOWER HOUSING ON HE STEERING
TUBE WITH A TUBE SECTION OF AN ADEQUATE DIAME-
TER.

Specific tooling

020021Y

Front suspension service tool

Vespa LX 50

Suspensions

SUSP - 97

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды