VESPA LX 50 Скачать руководство пользователя страница 42

Страница: 42 / 160

Brakes overheating

BRAKES OVERHEATING

Possible Cause

Operation

Defective piston sliding

Check calliper and replace any damaged part.

Brake disc or drum deformed

Using a dial gauge, check the planarity of the disk with the

wheel correctly fitted or the concentricity of the rear drum.

Electrical system

Battery

BATTERY

Possible Cause

Operation

Battery

The battery is the electrical device in the system that requires

the most frequent inspections and thorough maintenance. If the
vehicle is not used for some time (1 month or more) the battery

needs to be recharged periodically. The battery runs down

completely in the course of 5 ÷ 6 months. If the battery is fitted
on a motorcycle, be careful not to invert the connections, keep-

ing in mind that the black ground wire is connected to the

negative terminal while the red wire is connected to the terminal
. Follow the instructions in the ELECTRICAL SYSTEM

chapter for the recharging of the batteries.

Steering and suspensions

Heavy steering

STEERING HARDENING

Possible Cause

Operation

Torque not conforming

Check the tightening of the top and bottom ring nuts.

If irregularities continue in turning the steering even after mak-

ing the above adjustments, check the seats in which the ball

bearings rotate: replace if they are recessed.

Excessive steering play

EXCESSIVE STEERING CLEARANCE

Possible Cause

Operation

EXCESSIVE STEERING CLEARANCE

Check the tightening of the top and bottom ring nuts.

If irregularities continue in turning the steering even after mak-

ing the above adjustments, check the seats in which the ball

bearings rotate: replace if they are recessed.

Noisy suspension

NOISY SUSPENSION

Possible Cause

Operation

NOISY SUSPENSION

If the front suspension is noisy, check: the efficiency of the front
shock absorbers; the condition of the ball bearings and relevant

Troubleshooting

Vespa LX 50

TROUBL - 42

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды