VESPA LX 50 Скачать руководство пользователя страница 66

Страница: 66 / 160

Stationary driven half-pulley/Standard diame-
ter

Ø 33.965 to 33.985 mm

Stationary driven half-pulley / Minimum diam-
eter admitted after use

Ø 33.96 mm

Inspecting the driven sliding half-pulley

- Remove the 2 inner sealing rings and the two O-

rings.

- Measure the inside diameter of the mobile half-

pulley bushing.

Characteristic

Mobile driven half-pulley/ Maximum diameter
allowed

Ø 34.08 mm

- Check the belt contact surfaces.

- Insert the new oil seal and O-rings on the mobile

half-pulley.

- Fitting the half-pulley on the bushing.

Recommended products

AGIP GREASE SM 2

Grease for the C-ring of

the tone wheel

Soap-based lithium grease containing NLGI 2 Mo-

lybdenum disulphide; ISO-L-XBCHB2, DIN

KF2K-20

- Make sure the pins and collar are not worn, reassemble the pins and collar.

- Use a greaser with a curved spout to lubricate the driven pulley unit with around 6 g of grease. This

operation must be done through one of the holes inside the bushing until grease comes out of the

opposite hole. This procedure is necessary to prevent the presence of grease beyond the O-ring.

Recommended products

AGIP GREASE SM 2

Grease for the C-ring of the tone wheel

Soap-based lithium grease containing NLGI 2 Molybdenum disulphide; ISO-L-XBCHB2, DIN KF2K-20

Engine

Vespa LX 50

ENG - 66

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды