VESPA LX 50 Скачать руководство пользователя страница 70

Страница: 70 / 160

4) Check the integrity of the sliding blocks of the

contact plate.

- Check that the internal bushing shown in the fig-

ure is not abnormally worn and measure inside

diameter «

».

- Measure outside diameter «

» of the pulley slid-

ing bushing shown in the figure.

CAUTION

DO NOT LUBRICATE OR CLEAN THE BUSHING.

Characteristic

Driving pulley / Maximum diameter:

20.12 mm

Driving pulley/ Standard diameter:

20.021 mm

Driving pulley bushing/ Diameter maximum:

XXX mm

Driving pulley bushing/ Standard diameter:

20 -0.020/-0.041mm

Refitting the driving pulley

- Manually move the movable driven half-pulley

away by pulling it towards the clutch unit and insert

the belt observing the direction of rotation of the

first fitting.

N.B.

IT IS GOOD PRACTICE ALWAYS TO FIT THE BELT SO
THAT THE WORDS CAN BE READ IN CASE IT DOES NOT
SHOW A FITTING SIDE.

- Refit the components of the assembly (roller con-

tainer assembly with bushing, limiting washer, sta-

tionary half-pulley, cooling fan belt with drive,

washer and nut).

- With the specific tool, tighten the lock nut to 20

Nm and then perform a final 90° locking in order to

prevent the rotation of the driving pulley.

N.B.
REPLACE THE NUT WITH A NEW ONE AT EVERY REFIT
CAUTION
UPON FITTING THE DRIVING PULLEY UNIT IT IS OF UT-
MOST IMPORTANCE THAT THE BELT IS FREE INSIDE IN

Engine

Vespa LX 50

ENG - 70

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды