VESPA LX 50 Скачать руководство пользователя страница 40

Страница: 40 / 160

Possible Cause

Operation

to keep the cap in contact with the spark plug and the spark
plug grounded but away from its hole. Refit a dry spark plug

and start the vehicle.

Altered fuel characteristics

Drain off the fuel no longer up to standard; then, refill

Faulty spark plug

Remove the encrustation, restore the plug gap or replace being
sure to use the types of spark plug recommended at all times.

Bear in mind that many problems engines have, derive from

the use of the wrong spark plug

Intake joint cracked or with a bad seal

Replace intake joint and check for correct sealing on the head

Purifier-carburettor fitting damaged

Replace

Excessive oil consumption/Exhaust smoke

EXCESSIVE OIL CONSUMPTION/SMOKEY EXHAUST

Possible Cause

Operation

Excess of encrustations in the combustion chamber

Remove the encrustations

Engine tends to cut-off at full throttle

ENGINE STOP FULL THROTTLE

Possible Cause

Operation

Maximum nozzle dirty - lean mixture

Wash the nozzle with solvent and dry with compressed air

Dirty carburettor

Wash the carburettor with solvent and dry with compressed air

Water in the carburettor

Empty the tank through the appropriate bleed nipple.

Air filter dirty

Clean or replace

Defective floating valve

Check the proper sliding of the float and the functioning of the

valve

Tank breather hole obstructed

Restore the proper reservoir aeration

Engine tends to cut-off at idle

ENGINE STOP IDLING

Possible Cause

Operation

Minimum nozzle dirty

Wash the nozzle with solvent and dry with compressed air

Starter that stays open

Check: electric wiring, circuit continuity, mechanical sliding and

power supply

Reed valve does not close

Check / replace the reed pack

Wrong idling adjustment

Correctly adjust the engine idling and check the level of the

C.O.

Spark plug defective or faulty

Replace the spark plug with one with the specified degree and

check the plug gap

Excessive exhaust noise

INCREASED NOISINESS

Possible Cause

Operation

Secondary metal air pipe deteriorated

Check there are no leaks on the hoses on the crankcase and

the housing, check that there is a cap with filter and it is correctly

fitted to the transmission cover

Good condition of the missing secondary air circuit components

Check the individual components and the piping, check the

precision of the fitting. Replace the damaged components

Troubleshooting

Vespa LX 50

TROUBL - 40

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды