VESPA LX 50 Скачать руководство пользователя страница 96

Страница: 96 / 160

Specific tooling

020021Y

Front suspension service tool

- Use the tool fitted with part 20* and part 21* on

its stem as shown in the figure.

- Push the two roller casings with the handgrip until

their bottoms make contact with the pin end.

- Fit both dust guard rings «

» on the swinging hub

as shown in the detail drawing «

».

- Connect the swinging hub to the steering tube

with the guide pin, part 5*.

- Use the specific tool fitted with part 3* on its stem

and with part 4 at the bottom of the tool.

- Insert the previously greased pin on the swinging

hub and with the tool handgrip, move part 3 until it

stops on the steering tube.

- After fitting the pin, insert the two spacers, part

17*, slightly hitting with the mallet.

* Supplied with the tool

Specific tooling

020021Y

Front suspension service tool

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

Suspensions

Vespa LX 50

SUSP - 96

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды