VESPA LX 50 Скачать руководство пользователя страница 72

Страница: 72 / 160

Removing the wheel axle bearings

- Remove the oil seal and the Seeger ring.

- Remove the bearing by pushing from the outside

towards the inside of the gear compartment, using

the appropriate punch.

Specific tooling

020363Y

20-mm guide

020376Y

Adaptor handle

020358Y

37x40-mm Adaptor

Removing the driven pulley shaft bearing

- Remove the Seeger ring inside the cover.

- Remove the oil seal from the outside.

- Remove the centring dowels and position the

cover on a plane.

- Position the special tool on the internal track of

the bearing and remove said bearing with the aid

of a press.

Specific tooling

020452Y

Tube for removing and refitting the

driven pulley shaft

- Position the special tube on the internal raceway

of the bearing and from the shaft toothed side as

indicated in the figure. Expel the driven pulley shaft

with the aid of a press.

Specific tooling

020452Y

Tube for removing and refitting the

driven pulley shaft

Engine

Vespa LX 50

ENG - 72

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды