VESPA LX 50 Скачать руководство пользователя страница 95

Страница: 95 / 160

Steering column

Removal

After removing the upper seat, lean the vehicle on

one side and extract the steering tube completely

from the fork.

Specific tooling

020055Y

Wrench for steering tube ring nut

Overhaul

-The front suspension service operation is useful to replace the connecting parts between the steering

tube and the swinging hub of the front wheel holder, provided that the steering tube and the wheel holder

hub are in excellent conditions.

- Press and remove the wedging washer with the

help of a pointed end.

- For the second washer, repeat the operation us-

ing the punch on the side opposite to the one

shown in the figure.

= Ø12 Punch

= Sharp-edged end

- Use the specific tool, fitted with part 1*, and op-

erate the handgrip until the pin and the Nadella are

simultaneously ejected in the direction opposite

the tool thrusting force.

- To eject the second Nadella, use the tool fitted

with part 2* instead of part 1, on the side opposite

the one shown in the figure.

* Supplied with the tool

Vespa LX 50

Suspensions

SUSP - 95

Содержание LX 50

































































































































































Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды

VESPA LX 50, Руководство по ремонту

Результаты поиска

Содержание LX 50

Отзывы:

Похожие инструкции для LX 50

Бренды по названию

Популярные бренды