VESPA GTS Super 125 i.e. Скачать руководство пользователя

Страница: 143 / 285

Check the presence of fixed voltage between the

grey/black cable of the relay base and ground. If

there is none, check the continuity of the grey/

black cable between the fuse box (No. 3 15 A) and

the relay base.

N.B.

CONTINUITY TESTS MUST BE CARRIED OUT WITH THE
COMPONENTS DISCONNECTED. (RELAYS, CONTROL
UNIT, FUSES ETC.).

pump circuit6

Check, on switching to "ON", that there is battery

voltage, for about two seconds, to the Black-Green

cable of the pump connector and ground with

pump connector disconnected. Otherwise, check

the continuity of the Black-Green cable between

the pump connector and the remote control base.

Check the efficiency of the ground line of the fuel

pump by measuring the continuity between the

pump connector black cable, system side, and the

ground.

If, when switching to "ON", the pump continues to

turn after two seconds of activation, check, with the

control unit disconnected and the injection load re-

Vespa GTS Super 125 i.e.

Injection

INJEC - 143

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды