VESPA GTS Super 125 i.e. Скачать руководство пользователя страница 238

Страница: 238 / 285

Front mudguard

- First remove the steering tube and uncouple the

front brake pipes from the calliper in order to re-

move the front mudguard

- Remove the three mudguard-steering tube

clamps indicated in the figure

Radiator fan

- In order to carry out any operation on the radiator

unit, flow out the coolant in the coolant delivery

pipe in the pump, indicated in the photograph.

- Remove the shield back plate;

- Remove the coolant feed and return hoses from

the right radiator;

- Unscrew the 4 screws fixing the radiator to the

body;

- Detach the radiator

- Detach the pipe from the plastic duct by removing

the plastic clip shown in the photograph. Then re-

move the duct.

Chassis

Vespa GTS Super 125 i.e.

CHAS - 238

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды