VESPA GTS Super 125 i.e. Скачать руководство пользователя

Страница: 96 / 285

Make sure air bubbles are rising from all six filling holes. Leave the container in this position for 20

minutes or more.

Note:

If there are no air bubbles coming out of the filling holes, lightly tap the bottom of the container

two or three times. Do not remove the container from the battery.

5) Take out the container.

Make sure all the electrolyte in the battery is drained. Gently tap the bottom of the container if electrolyte

remains in the container. Now, gently pull the container out from the battery, only do this when the

container is completely empty, and proceed immediately to the next point.

6) Battery closing.

Insert the airtight cover strips into the filling holes. Press horizontally with both hands and make sure

that the strip is levelled with the top part of the battery.

Note:

To do this, do not use sharp objects that could damage the closing strip, use gloves to protect

your hands and do not bring your face close to the battery.

The filling process is now complete.

Do not remove the strip of caps under any circumstances, do not add water or electrolyte.

Place the battery down for 1 to 2 hours prior to the charging from the battery.

7) Recharging the new battery

With the above-mentioned procedure, the battery

will have gained around 70% - 75% of its total

electrical capacity. Before installing the battery on

the vehicle, it must be fully charged and then must

be recharged.

If the battery is to be installed on the vehicle

prior to this pre-charged one, the battery will

not be able to exceed 75% charge without jeop-

ardising its useful life on vehicle.

The dry charge battery MF like the completely loa-

ded YTX, must have a no-load voltage between

12.8 - 13.15 V Bring the battery to full charge, us-

ing the 020648Y battery charger:

a - select the type of battery with the red switch on

the left of the panel battery charger panel

b - select NEW on the yellow timer

c - connect the clamps of the battery charger to the

battery poles (black clamp to negative pole (-) and

red clamp to positive pole (+)).

Electrical system

Vespa GTS Super 125 i.e.

ELE SYS - 96

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды