VESPA GTS Super 125 i.e. Скачать руководство пользователя страница 171

Страница: 171 / 285

Check the efficiency of the injection load relay.

Check the resistance of the energising coil be-

tween pins 86 and 85: 40 to 80 Ohm

Apply a voltage of 12V to pins 86 and 85; make

sure that there is continuity between pins 30 and

87 of the relay.

Check the power supply line of the injection load

relay energising coil: after switching to "ON", make

sure there is battery voltage, for 2 seconds, be-

tween the Red-White cable and Black-Purple ca-

ble of the relay base. If there is not, check the

continuity of the Red-White cable between the

fuse box and the relay base and of the Black-Pur-

ple cable between the pin 22 of the control unit and

the relay base.

N.B.

CONTINUITY TESTS MUST BE CARRIED OUT WITH THE
COMPONENTS DISCONNECTED. (RELAYS, CONTROL
UNIT, FUSES ETC.).

Vespa GTS Super 125 i.e.

Injection

INJEC - 171

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды