manualshive.com logo in svg

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Поделиться
Скачать
VESPA GTS Super 125 i.e. Скачать руководство пользователя страница 93

Specification

Desc./Quantity

Protected circuits:

 Vehicle main fuse

2

Fuse 2

Current rating

: 7.5A

Protected circuits:

 Running lights and instrument panel

illumination power

3

Fuse 3

Current rating

: 7.5A

Protected circuits:

 Live services circuit

4

Fuse 4

Current rating

: 7.5A

Protected circuits:

 Live injection ECU

5

Fuse 5

Current rating

: 7.5A

Protected circuits:

 Battery power for accessories and

instrument panel

6

Fuse 6

Current rating

: 15A

Protected circuits:

 Battery power for headlight and sad-

dle release system.

7

Fuse 7

Current rating

: 15A

Protected circuits:

 Injection load power supply.

THE FOLLOWING INFORMATION REFER TO THE VERSION EQUIPPED WITH MIU G3 ECU.

The electrical system is equipped with:

1. six protection fuses «

A

» located in the glove compartment to the left

2. of a fuse «

B

», located in the battery compartment.

The chart shows the position and specifications of the fuses in the vehicle.

CAUTION

BEFORE REPLACING A BLOWN FUSE, FIND AND SOLVE THE FAILURE THAT CAUSED IT TO
BLOW. NEVER TRY TO REPLACE THE FUSE WITH ANY OTHER MATERIAL (E.G., A PIECE OF
ELECTRIC WIRE).

CAUTION

MODIFICATIONS OR REPAIRS TO THE ELECTRICAL SYSTEM, PERFORMED INCORRECTLY OR
WITHOUT STRICT ATTENTION TO THE TECHNICAL SPECIFICATIONS OF THE SYSTEM CAN
CAUSE MALFUNCTIONING AND RISK OF FIRE.

FUSES

Specification

Desc./Quantity

1

Fuse 1

Current rating

: 30 A

Protected circuits:

 Vehicle main fuse

2

Fuse 2

Current rating

: 7.5A

Protected circuits:

 Key powered ECU, immobilizer aer-

ial, electric fan relay, injection load relay.

3

Fuse 3

Current rating

: 15A

Protected circuits:

 Battery-powered load and injection

control unit.

4

Fuse 4

Current rating

: 7.5A

Protected circuits:

 Key powered to headlight relay

switch, pre-installation for anti-theft device , turn indica-

tor control device, instrument panel, horn, stop.

5

Fuse 5

Current rating

: 7.5 A

Protected circuits:

 Battery power for headlight, electric

fan and saddle release.

6

Fuse 6

Current rating

: 7.5A

Protected circuits:

 Battery power for pre-installation for

anti-theft device and instrument panel.

7

Fuse 7

Current rating

: 7.5A

Protected circuits:

 Key powered to daylight running

light and instrument panel lighting.

Vespa GTS Super 125 i.e.

Electrical system

ELE SYS - 93

Содержание GTS Super 125 i.e.






























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды