VESPA GTS Super 125 i.e. Скачать руководство пользователя страница 206

Страница: 206 / 285

- Hold the full silent bloc bracket in the clamp

- Using the appropriate tool, remove the silent bloc

from the bracket from the side corresponding to

the inside of the vehicle. This is to guarantee the

tool is centred properly on the support

- Install a new silent bloc, making sure it aligns

properly with the reference tooth.

- Fit the silent blocs, making sure the chamfered

part of the silent bloc matches the chamfered part

of the bracket

- Using the appropriate tool, fit the silent bloc as

shown in the picture

Refitting

- To refit, perform the removal operations in reverse.

- Grease the bearings and the rolling parts with the recommended grease.

Suspensions

Vespa GTS Super 125 i.e.

SUSP - 206

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды