VESPA GTS Super 125 i.e. Скачать руководство пользователя

Страница: 162 / 285

Disconnect the fuel pipe connector. Start up the

engine and wait for it to stop. With the wiring con-

nected to the control unit and system try to start up

the engine and check that the voltage between

pins 13 and 15 is around 2.8 V

With the interface cable harness disconnected

from the control unit, check continuity between pin

13 and the red cable of the engine speed sensor

connector and between pin 15 and the brown ca-

ble of the engine speed sensor connector

With the interface wiring and rpm sensor connec-

tor disconnected from the control unit, check that

the Red and Brown cables (pin 13 - 15) are isola-

ted from each other and insulated from the ground.

Specific tooling

020481Y

Control unit interface wiring

020331Y

Digital multimeter

THE FOLLOWING INFORMATION REFER TO THE VERSION EQUIPPED WITH MIU G3 ECU.

Injection

Vespa GTS Super 125 i.e.

INJEC - 162

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Похожие инструкции для GTS Super 125 i.e.

Бренды по названию

Популярные бренды