VESPA GTS Super 125 i.e. Скачать руководство пользователя страница 207

Страница: 207 / 285

-Complete the fitting by tightening the nuts on the relative bolts to the proper tightening torque.

Locking torques (N*m)

Engine- and vehicle-side swinging arm junction bolt

40 ÷ 45

Swinging arm pin - Engine

64 ÷ 72

Body shell - Swinging arm pin

76 ÷ 83

Screw fixing the silent-block support plate to the body

÷ 52

Shock absorbers

Removal

Proceed as follows:

- place the vehicle on its centre stand;

- remove the luggage rack

- lift the engine a little with a jack so as to free the

two shock absorbers;

- remove the muffler assembly;

- undo the shock absorber spring assembly clamp-

ing screw from the support fixed to the engine on

the one side and from that fixed to the muffler on

the other;

- unscrew the two upper nuts (one on each side)

fixing the shock absorber spring assembly to the

frame and remove the shock absorbers.

Refitting

To refit, carry out the above removal operations in reverse order, observing the prescribed torques.

Locking torques (N*m)

Vespa GTS Super 125 i.e.

Suspensions

SUSP - 207

Содержание GTS Super 125 i.e.






























































































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции

Результаты поиска

Содержание GTS Super 125 i.e.

Отзывы:

Бренды по названию

Популярные бренды