manualshive.com logo in svg

VESPA GTS Super 125 i.e., Руководство по обслуживанию станции


Поделиться
Скачать
background image

Battery installation

VRLA battery (valve-regulated lead-acid battery) Maintenance Free (MF)

WARNING

BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SUL-
PHURIC ACID. AVOID CONTACT WITH YOUR EYES, SKIN AND CLOTHING. IN CASE OF CON-
TACT WITH YOUR EYES OR SKIN, RINSE WITH ABUNDANT WATER FOR ABOUT 15 MINUTES
AND SEEK IMMEDIATE MEDICAL ATTENTION.
IN THE EVENT OF ACCIDENTAL INGESTION OF THE LIQUID, IMMEDIATELY DRINK LARGE
QUANTITIES OF WATER OR MILK. MAGNESIUM MILK, BATTERED EGG OR VEGETABLE OIL.
SEEK IMMEDIATE MEDICAL ATTENTION.
BATTERIES PRODUCE EXPLOSIVE GASES; KEEP CLEAR OF NAKED FLAMES, SPARKS OR
CIGARETTES; VENTILATE THE AREA WHEN RECHARGING INDOORS.
ALWAYS PROTECT YOUR EYES WHEN WORKING CLOSE TO BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

1) Battery preparation

Position the battery on a flat surface. Remove the

adhesive sheet closing cells and proceed as quick-

ly as possible to run the subsequent activation

phases.

2) Electrolyte preparation.

Remove the container of the electrolyte from the

pack. Remove and preserve cover strips from the

container, in fact, the strip will later be used as a

closing cover.

Note:

 Do not pierce the sealing of the container or

the container itself because inside there is sulphu-

ric acid.

3) Procedure for filling the battery with acid.

Position the electrolyte container upside down with

the six areas sealed in line with the six battery filler

holes. Push the container down with enough force

to break the seals. The electrolyte should start to

flow inside the battery.

Note:

 Do not tilt the container to prevent the flow

of electrolyte from pausing or stopping.

4) Control the flow of electrolyte

Vespa GTS Super 125 i.e.

Electrical system

ELE SYS - 95

Содержание GTS Super 125 i.e.






























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GTS Super 125 i.e.

DAXYS GRIZZLY User Manual preview
GRIZZLY
Бренд: DAXYS Страницы: 30
W-Tec 23784 User Manual preview
23784
Бренд: W-Tec Страницы: 13
Narex ESN 350 Original Operating Manual preview
ESN 350
Бренд: Narex Страницы: 110
Velotric Thunder 1 Quick Start Manual preview
Thunder 1
Бренд: Velotric Страницы: 15
Razor Kiddie Owner'S Manual And Safety Handbook preview
Kiddie
Бренд: Razor Страницы: 4
Zizito ARLY Manual preview
ARLY
Бренд: Zizito Страницы: 38
C.T.M. HS-575 Instruction Booklet preview
HS-575
Бренд: C.T.M. Страницы: 22
PIAGGIO Liberty 50 4tempi 2008 Workshop Manual preview
Liberty 50 4tempi 2008
Бренд: PIAGGIO Страницы: 195
Billow Technology URBAN85 User Manual preview
URBAN85
Бренд: Billow Technology Страницы: 38
Suzuki Burgman Series Owner'S Manual preview
Burgman Series
Бренд: Suzuki Страницы: 141
Ignite ESC02 User Manual preview
ESC02
Бренд: Ignite Страницы: 7
Ride VOLO K05 User Manual preview
K05
Бренд: Ride VOLO Страницы: 16
Ride VOLO K02 User Manual preview
K02
Бренд: Ride VOLO Страницы: 18
Ride1up Cafe Cruiser Owner'S Manual preview
Cafe Cruiser
Бренд: Ride1up Страницы: 22
Roma Medical Monza User Manual preview
Monza
Бренд: Roma Medical Страницы: 16
Derby cycle Pedelec Integrale 0.5 Original User Manual preview
Pedelec Integrale 0.5
Бренд: Derby cycle Страницы: 64
ROOES SMARTE-SCOOTER Manual preview
SMARTE-SCOOTER
Бренд: ROOES Страницы: 12
Neodrives Smart MMI User Manual preview
Smart MMI
Бренд: Neodrives Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды