manualshive.com logo in svg

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию


Поделиться
Скачать
background image

C

OMPONENT

 T

RANSPOSITION

Specification

Desc./Quantity

1

Instrument panel

2

Throttle body and electronic injection control unit (MIU)

3

Diagnostics socket connector

4

Fuel pump

5

Water temperature sensor

6

Fuel injector

7

HV coil

8

Engine speed sensor

9

Lambda probe

10

Injection load remote control

11

Battery

12V - 12 Ah

12

Electric fan remote control

MIU injection system

This vehicle is fitted with an integrated injection and ignition system.

Injection is indirect in the manifold through an electro-injector.

The injection and ignition are timed on the four-stroke cycle by means of a tone wheel keyed on to the

crankshaft (24-2 teeth) and pick-up sensor.

Combustion and ignition are managed on the basis of engine revs and throttle valve opening. Further

corrections are made according to the following parameters:

- Coolant temperature.

- Intake air temperature

- Lambda probe

The system implements an idle feeding correction with cold engine through a Stepper motor on a by-

pass circuit of the throttle valve. The control unit manages the Stepper motor and the injector opening

time, thereby ensuring the idle steadiness and the proper combustion.

In all conditions of use, mixture preparation is managed by modifying the injector opening time.

The fuel system pressure is kept constant based on the ambient pressure.

The 

fuel system circuit

 consists of:

- Fuel pump

- Fuel filter

- Injector

- Pressure regulator

The pump, the filter and the regulator are placed inside the fuel tank on a single support.

The injector is connected by a pipe with fast-release fittings. The pressure regulator is located at the

beginning of the circuit.

The fuel pump is controlled by the MIU control unit; this ensures the scooter safety

The 

ignition circuit

 consists of:

- HV coil

- HV cable

- Shielded cap

- MIU control unit

Vespa GTS Super 125 i.e. (2009)

Injection

INJEC - 97

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GTS Super 125 i.e. (2009)

Razor RipStik Electric Owner'S Manual preview
RipStik Electric
Бренд: Razor Страницы: 16
Kayoba 008015 Operating Instructions Manual preview
008015
Бренд: Kayoba Страницы: 44
Merits Health Products S-131 Quick Reference Manual preview
S-131
Бренд: Merits Health Products Страницы: 26
haibike XDURO Owner'S Manual preview
XDURO
Бренд: haibike Страницы: 82
techtron Ultra 5000 Instruction Manual preview
Ultra 5000
Бренд: techtron Страницы: 20
Merits S139 User Manual preview
S139
Бренд: Merits Страницы: 30
Razor 13100E-BL Owner'S Manual preview
13100E-BL
Бренд: Razor Страницы: 24
Jack JACKRABBIT Owner'S Manual preview
JACKRABBIT
Бренд: Jack Страницы: 2
BLUETOUCH BT800 Instruction Manual preview
BT800
Бренд: BLUETOUCH Страницы: 73
CITY BOSS GT8 User Manual preview
GT8
Бренд: CITY BOSS Страницы: 48
Osotto ES-M13 User Manual preview
ES-M13
Бренд: Osotto Страницы: 22
Shoprider 889-3XLS User Manual preview
889-3XLS
Бренд: Shoprider Страницы: 20
Vermeiren Venus 4 Sport Instruction Manual preview
Venus 4 Sport
Бренд: Vermeiren Страницы: 200
Segway Ninebot Bike User Manual preview
Ninebot Bike
Бренд: Segway Страницы: 9
Enjoybot H5 Owner'S Manual preview
H5
Бренд: Enjoybot Страницы: 4
e-TWOW BOOSTER PLUS User Manual preview
BOOSTER PLUS
Бренд: e-TWOW Страницы: 76
E-Wheels EW-46 Service & Repair Manual preview
EW-46
Бренд: E-Wheels Страницы: 46
Nipponia Neon Owner'S Manual preview
Neon
Бренд: Nipponia Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды