VESPA GTS Super 125 i.e. (2009) Скачать руководство пользователя

Страница: 66 / 234

45.

Injector ECU

Lights and turn indicators

12V-12Ah Battery

30A Fuse

15A Fuse

10.

Key switch contacts

13.

Light switch

17.

Front and rear daylight bulbs and license plate

light

18.

Headlight with twin-filament bulb

20.

Turn indicator bulbs

21.

Turn indicator switch

22.

Turn indicator control device

23.

Instrument panel

26.

Headlight remote control

27.

Fuse 7.5A

28.

Fuse 7.5A

29.

Fuse 15A

30.

Fuse 7.5A

31.

Fuse 7.5A

45.

Injector ECU

Checks and inspections

This section is devoted to the checks on the electrical system components.

Immobiliser

The electronic ignition system is controlled by the

control unit with the integrated Immobilizer sys-

tem. The immobilizer is an anti-theft system that

allows the vehicle to be operated only when it is

started with coded keys recognised by the control

unit. The code is integrated in a transponder in the

key block. This allows the driver clear operation

without having to do anything other than just turn-

ing the key. The Immobilizer system consists of the

following components:

Electrical system

Vespa GTS Super 125 i.e. (2009)

ELE SYS - 66

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию

Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды