VESPA GTS Super 125 i.e. (2009) Скачать руководство пользователя страница 120

Страница: 120 / 234

With injector disconnected and the injector load

remote control disconnected, check the continuity

of the Black-Green cable between the injector con-

nector and remote control base.

Inspecting the injector hydraulics

To carry out the injector check, remove the intake

manifold by removing the three clamping screws

at the head and the clip connecting the control unit

to the manifold.

Install the appropriate tool for checking fuel pres-

sure and position the manifold over a container

graduated by at least 100 cm³. Connect the injec-

tor with the cable making up part of the supply for

the injection tester. Connect the clamps of the ca-

ble to an auxiliary battery. Activate the fuel pump

with the active diagnosis. Check that, within fifteen

seconds, approximately 40 cm³ of fuel is dis-

pensed with an adjustment pressure of approxi-

mately 2.5 BAR.

Specific tooling

020480Y

Petrol pressure check set

Injection

Vespa GTS Super 125 i.e. (2009)

INJEC - 120

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию

Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды