VESPA GTS Super 125 i.e. (2009) Скачать руководство пользователя страница 47

Страница: 47 / 234

ing can be cleaned off by removing the two rubber

caps «

».

CAUTION

IF THE VEHICLE IS USED ON DUSTY ROADS, IT IS NEC-
ESSARY TO SERVICE THE AIR FILTER MORE OFTEN TO
AVOID DAMAGING THE ENGINE.

Recommended products

AGIP FILTER OIL

Oil for air filter sponge

Mineral oil with specific additives for increased ad-

hesiveness

Engine oil

In 4T engines, the engine oil is used to lubricate the distribution elements, the bench bearings and the

thermal group.

An insufficient quantity of oil can cause serious damage to the engine.

In all 4T engines, the deterioration of the oil characteristics, or a certain consumption should be con-

sidered normal, especially if during the run-in period. Consumption levels in particular can be influenced

by the conditions of use (e.g.: oil consumption increases when driving at "full throttle".

Replacement

At 1,000 km and after every 10,000 km, the oil and

the filter must be changed. The engine must be

drained by running off the oil from drainage cap

" of the flywheel side gauze pre-filter; further-

more to facilitate oil drainage, loosen the cap/

dipstick "

". Once all the oil has drained through

the drainage hole, unscrew the oil cartridge filter

" and remove it.

Make sure the pre-filter and drainage plug O-rings

are in good conditions.

Lubricate them and refit the mesh filter and the oil

drainage plug, screwing them up to the prescribed

torque.

Vespa GTS Super 125 i.e. (2009)

Maintenance

MAIN - 47

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию

Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды