VESPA GTS Super 125 i.e. (2009) Скачать руководство пользователя

Страница: 152 / 234

- Check the entire swinging arm assembly.

- Check all the centring bushing components and

silent block rubber buffers.

- Replace the work components that cause exces-

sive clearance on the rear suspension.

Overhaul

- Check there is no sticking in the movement of the

connection of the swinging arm on the engine side

to the swinging arm on the chassis side.

- Check the axial clearance between the two

swinging arms using a feeler gauge

Characteristic

Standard clearance

0.40 ÷ 0.60 mm

Allowable limit after use:

1.5 mm

- To check the clearance on the chassis-side arm,

mount the retainer using the pin fixing the swinging

arm to the chassis and two adaptor rings of the

appropriate tool 020229Y. Alternatively use two

washers with inner diameter for 12-mm pins, min.

outer diameter: 30 mm: min. thickness: 4 mm.

- Check there is no sticking in the rotation.

- Check the axial clearance of the swinging arm on

the chassis side

Characteristic

Standard clearance

0.40 ÷ 0.60 mm

Allowable limit after use:

1.5 mm

Suspensions

Vespa GTS Super 125 i.e. (2009)

SUSP - 152

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию

Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды