VESPA GTS Super 125 i.e. (2009) Скачать руководство пользователя страница 163

Страница: 163 / 234

- that the cylinder and the floating body of the cal-

liper do not show signs of scratches or erosion,

otherwise replace the entire calliper;

- that the guides of the fixed plate are not scratched

or eroded, otherwise replace the entire plate;

- that the brake pad check spring works properly.

CAUTION

ALL THE INTERNAL COMPONENTS MUST BE REPLACED
EVERY TIME THE CALLIPER IS SERVICED.

The brake pad check spring

1. pad fixing screws

2. reaction plate fixing screws

3. reaction plate

4. fixed plate

5. floating body

6. piston

7. piston sealing rings

8. guide protection rubbers

9. brake pad check spring

10. pads

Refitting

Insert the following on the front brake body:

-The sealing rings and the pistons (1).

-Refit the plate (2).

- Arrange the pad holding clamp (3).

-Refit the pads and bleed air.

-Place the calliper on the disk and lock it to the

support by tightening the bolts at the prescribed

torque.

-Lock the pipe joint to the calliper at the prescribed

torque.

CAUTION

ALWAYS USE NEW COPPER WASHERS.

Locking torques (N*m)

Screws fixing the front calliper to the sup-
port:

24 ÷ 27

Screw fixing the oil connection to

the calliper

19 ÷ 24

Vespa GTS Super 125 i.e. (2009)

Braking system

BRAK SYS - 163

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию

Результаты поиска

Содержание GTS Super 125 i.e. (2009)

Отзывы:

Похожие инструкции для GTS Super 125 i.e. (2009)

Бренды по названию

Популярные бренды