manualshive.com logo in svg

VESPA GTS Super 125 i.e. (2009), Руководство по обслуживанию


Поделиться
Скачать
background image

Refit the new cartridge filter being careful to lubri-

cate the O-ring before fitting it.

Change the engine oil.

Since a certain quantity of oil still remains in the

circuit, oil must be filled from cap "

A

". Then start

up the scooter, leave it running for a few minutes

and switch it off: after five minutes check the level

and if necessary top up without exceeding the

MAX

 level. The cartridge filter must be replaced

every time the oil is changed. Use new oil of the

recommended type for topping up and changing

purposes.

N.B.

THE ENGINE MUST BE HOT WHEN THE OIL IS CHANGED.

Recommended products

AGIP CITY HI TEC 4T

 

Engine oil

SAE 5W-40 Synthetic oil that exceed the require-

ments of API SL, ACEA A3, JASO MA specifica-

tions

Check

This operation must be carried out with the engine cold and following the procedure below:

1. Place the vehicle on its centre stand and on flat ground.

2. Undo cap/dipstick "

A

", dry it off with a clean cloth and replace it, 

screwing down completely

.

3. Remove the cap/dipstick again and check that the level is between the min and max. marks; top-

up, if required.

The MAX level mark indicates a quantity of around 1300 cc of engine oil. If the check is carried out after

the vehicle has been used, and therefore with a hot engine, the level line will be lower; in order to carry

out a correct check, wait at least 10 minutes after the engine has been stopped so as to get the correct

level.

Oil top-up

The oil should be topped up after having checked

the level and in any case by adding oil 

without

ever exceeding the MAX. level

.

Restoration of the level from 

MIN

 to 

MAX

 requires

approximately 

200 cc

.

Maintenance

Vespa GTS Super 125 i.e. (2009)

MAIN - 48

Содержание GTS Super 125 i.e. (2009)











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GTS Super 125 i.e. (2009)

V&D Electric Bikes Scoot E-3 Instructions Manual preview
Scoot E-3
Бренд: V&D Electric Bikes Страницы: 10
Izip E3 Peak System Operation Manual preview
E3 Peak
Бренд: Izip Страницы: 8
E-max 100LD User Manual preview
100LD
Бренд: E-max Страницы: 42
Invacare Pronto Air User Manual preview
Pronto Air
Бренд: Invacare Страницы: 64
KYMCO DJR 50 (Spanish) Manual preview
DJR 50
Бренд: KYMCO Страницы: 43
Magic INMotion Super Space Scooter User Manual preview
Super Space Scooter
Бренд: Magic INMotion Страницы: 8
WHILL C2 Operating Manual preview
C2
Бренд: WHILL Страницы: 12
Daymak Boomerbugy II Owner'S Manual preview
Boomerbugy II
Бренд: Daymak Страницы: 32
Polaris PES 0504 Manual Instruction / Warranty preview
PES 0504
Бренд: Polaris Страницы: 34
Electra Accessories VOY 88911 Assembly And User'S Manual preview
VOY 88911
Бренд: Electra Accessories Страницы: 14
RIEJU E-City User Manual preview
E-City
Бренд: RIEJU Страницы: 50
Golden GB-106 Buzzaround Lite Owner'S Manual preview
GB-106 Buzzaround Lite
Бренд: Golden Страницы: 40
JUPITERBIKE DEFIANT User Manual preview
DEFIANT
Бренд: JUPITERBIKE Страницы: 42
Shoprider Dasher 3 User Manual preview
Dasher 3
Бренд: Shoprider Страницы: 20
Scooterpac Ignite User Manual preview
Ignite
Бренд: Scooterpac Страницы: 44
TN’G TN'G DR150cc Owner'S Manual preview
TN'G DR150cc
Бренд: TN’G Страницы: 65
Baja motorsports SC150 HSun 150cc Owner'S Manual preview
SC150 HSun 150cc
Бренд: Baja motorsports Страницы: 44
Tanaka MOBY XL Service Manual preview
MOBY XL
Бренд: Tanaka Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды