VESDA VLC Скачать руководство пользователя | Manualshive

Страница: 21 / 58

background image

VESDA

VESDA Maintenance Guide

www.xtralis.com

15

7

Annual Testing

Local code guidelines may state that system and detector tests be conducted on a regular basis. Xtralis
recommends that such tests be conducted, at least, annually. However, there are some environments in
which it is necessary to conduct maintenance and testing more frequently, refer to Appendix B on page 49.

Notes:

l

A sample maintenance and testing log is provided in Appendix C on page 51.

l

Xtralis strongly recommends that all persons who install, commission, service and maintain VESDA
systems attend the VESDA accreditation training. Please contact your local Xtralis office for more
information.

7.1

Detector Tests

Check the following items to ensure that performance is still satisfactory:

1. Recorded faults - If any faults are present, record and rectify them before beginning any maintenance.
2. Power supply - Ensure that the input voltage is within the operating requirements.
3. Backup battery (if installed) - Check that the batteries are fully charged and the charging voltage is

functioning correctly.

4. Airflow - Check the airflow for each sampling pipe in use. Compare to previous site visit data to ensure

that there is no degradation in performance due to pipe blockages, leaks, breaks or contamination.

5. Smoke test - Inject an appropriate level of smoke into the required sampling holes.
6. Record Transport Time - This figure should be consistent with your previous maintenance visit or your

original commissioning documentation. Refer to your local standards for allowable variations.

7. Local detector display - Ensure that the detector's front panel display responds appropriately to any faults

and smoke levels, within the time specified in your local code guidelines.

8. Relay performance - Ensure that the detector's fire and fault relays are functioning correctly.
9. Remote detector display - Ensure that any associated remote detector displays (if installed) respond

appropriately to any faults and smoke levels, within the time specified in your local code guidelines.

10. Record results - Xtralis recommends that you photocopy the sample maintenance log in Appendix C on

page 51 and record all results on the copy. Store the log in an appropriate known location on-site.

11. Compare all results to previous recorded tests - Ensure that there is no degradation in performance. If a

noticeable change is observed, maintenance of the detector and/or sampling pipe network may be
necessary.

12. Schedule next visit - Determine the appropriate time for the next site visit by referring to Appendix B on

page 49.

7.2

System Fire Panel Notification Tests

Your detector alarm and fault tests should register on the monitoring system, within a time frame consistent
with local standards. System notification results should be recorded in the detector maintenance log.

«
...
19
20
21
22
23
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: Eaglemaster Страницы: 7

Ei 3105TYCH Optical

Бренд: Ei Electronics Страницы: 2

Бренд: Hama Страницы: 18

Fire-Lite SD350

Бренд: Pittway Страницы: 2

Бренд: Autostart Страницы: 11

Prestige 128-8601

Бренд: Audiovox Страницы: 8

Бренд: Casio Страницы: 5

Бренд: Casio Страницы: 4

Бренд: Casio Страницы: 12

Бренд: Fenwal Страницы: 13

Бренд: IKEA Страницы: 12

Бренд: Traeger Страницы: 4

Бренд: Traeger Страницы: 18

Smoking Gun Pro CSM700

Бренд: Breville Страницы: 24

Бренд: Abus Страницы: 24

Бренд: Abus Страницы: 92

Бренд: Eurochron Страницы: 8

Бренд: La Crosse Technology Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды