VESDA VLC Скачать руководство пользователя | Manualshive

Страница: 40 / 58

background image

VESDA Maintenance Guide

VESDA

34

www.xtralis.com

Figure 8-22: Intelligent Filter Removal

5. Remove the three Aspirator screws (A) and the two screws on the exhaust port (B).
6. Remove the Aspirator (C).

B

A

C

Figure 8-23: Aspirator Replacement

7. Flip the aspirator and disconnect the Aspirator cable.

Reinstall the replacement Aspirator

1. Ensure that the 24V input is still disconnected.
2. Connect the aspirator cable.
3. Install the new aspirator (C), the three aspirator screws (A) and the two screws on the exhaust port (B).
4. Reinstall the Intelligent Filter.
5. Power up the detector by reattaching the 24V supply.
6. Wait approximately 10 minutes to ensure that the detector does not report any fault conditions.
7. Perform a smoke test and ensure detector response is as per commissioning data.
8. If the replacement aspirator is brand new, execute the

Reset Aspirator Life

command in Xtralis VSC.

8.4.4

Replacing the VESDA VLI Chamber Assembly

Notes:

l

It is important to precisely follow the sequence below in order to avoid kinking the tubes.

l

Remove the longer tube near the secondary filter first, followed by the shorter tube near the aspirator.

Requirements

l

Philips head screwdriver

l

10mm spanner or flat-blade screwdriver

Remove the Detection Chamber Assembly

1. Set the detector to Standby mode.
2. Remove the front cover.
3. Power down the detector by removing the 24V input.
4. Remove the Intelligent Filter (Figure 8-24). Refer to Section 8.4.1 on page 32 for further information.

Figure 8-24: Intelligent Filter Removal

«
...
38
39
40
41
42
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: Magicar Страницы: 13

Бренд: Deling Electron Страницы: 4

Бренд: Daffodil Страницы: 3

Great Outdoors Smoky Mountain 3425GLA

Бренд: Landmann Страницы: 27

Бренд: Xpresskit Страницы: 20

Бренд: AVS Страницы: 4

Excalibur ATV-1000

Бренд: Omega Страницы: 34

Бренд: Masterbuilt Страницы: 6

Бренд: Uniden Страницы: 12

Бренд: Uniden Страницы: 8

Бренд: GST Страницы: 2

Бренд: Xtralis Страницы: 40

Бренд: TFA Страницы: 2

Бренд: TFA Страницы: 50

Бренд: RED Страницы: 2

Бренд: bolid Страницы: 2

Бренд: Equity Страницы: 2

Бренд: Equity Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды