VESDA VLC Скачать руководство пользователя | Manualshive

Страница: 35 / 58

background image

VESDA

VESDA Maintenance Guide

www.xtralis.com

29

Figure 8-16: Replacing the Aspirator in a VESDA VLC detector

9. Check that the new aspirator has a gasket on the inlet flange and three attached screws.

10. Wipe the manifold outlet flange surface.
11. Secure the aspirator with the three screws.
12. Reconnect the previously removed air hose to the pipe on the aspirator. Ensure a tight fit over the pipe.
13. Reinsert the termination card into the interface card.
14. Secure the termination card with the four screws.
15. Connect the aspirator cable connector to the socket on the aspirator; the connector is keyed and can only

be inserted one way.

16. Check that all wires are secured to their connectors or terminals.
17. Power up the detector and check that the aspirator is running.
18. Resolve all Fault conditions.
19. Close the detector.
20. Reset Isolate to normal conditions and check that the airflow % has returned to the level it was at before

Disassembly.

«
...
33
34
35
36
37
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Smart Pro DXL-1920L

Бренд: Pandora Страницы: 21

Бренд: Directed Electronics Страницы: 58

Бренд: Prestige Страницы: 8

Бренд: Lang BBQ Smokers Страницы: 2

Бренд: Prestige Страницы: 19

Бренд: VESDA Страницы: 116

Бренд: AUTHOR Alarm Страницы: 48

Бренд: AUTHOR Alarm Страницы: 44

Бренд: IKEA Страницы: 40

Бренд: iHome Страницы: 12

lisa RF time flash

Бренд: HumanTechnik Страницы: 52

Бренд: Steren Страницы: 32

Бренд: DEI Страницы: 23

Бренд: La Crosse Technology Страницы: 8

Бренд: Airam Страницы: 2

Бренд: jablotron Страницы: 16

Бренд: Universal Страницы: 7

Бренд: Prestige Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды