VESDA VLC Скачать руководство пользователя | Manualshive

Страница: 33 / 58

background image

VESDA

VESDA Maintenance Guide

www.xtralis.com

27

8.2

VESDA VLC

8.2.1

Replacing the VESDA VLC Filter Cartridge

The service interval of an air filter depends upon the environment. You can use the LCD Programmer or Xtralis
VSC Software to change the service interval for filters. The system will generate a minor fault when the filter
has reached 80% and an urgent fault when it reaches 120% of its capacity. We recommend that the
installation date and replacement date are written on the air filter cartridge label as a physical reminder of when
the next service is expected.

Note:

The detector must have the power turned on when the air filter cartridge is being replaced.

Replacement Procedure

1. Open the front cover
2. Locate the air filter cartridge (A), inside the detector compartment, as indicated in Figure 8-15 below.
3. Undo the recessed philips head filter screw (B) in Figure 8-15 below.
4. Lift out the air filter cartridge.

Figure 8-15: Replacing the air filter cartridge in VESDA VLC detectors

5. Insert a new air filter cartridge (A) in Figure 8-15 above.
6. Tighten the filter screw (B) in Figure 8-15 above.
7. Reset the filter counter by connecting a LCD programmer or a PC with Xtralis VSC software to the

programming socket.

8. Using a PC only (applicable to RO version) or a PC with a PC-Link HLI (Applicable to VN version only),

reset the filter by entering your user level and PIN number to Log ON to the detector then Initiate the
Reset Filter Settings command located under the device menu.

9. Close up the detector.

«
...
31
32
33
34
35
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: La Crosse Technology Страницы: 8

Бренд: LST Страницы: 2

Бренд: Magnavox Страницы: 21

Бренд: jablotron Страницы: 2

NIGHT VISION 30330B

Бренд: Equity Страницы: 2

Бренд: FONRI Страницы: 132

Бренд: Sharper Image Страницы: 5

Бренд: Sharper Image Страницы: 4

Travel Soother SI601

Бренд: Sharper Image Страницы: 7

Бренд: Hama Страницы: 13

Бренд: Hama Страницы: 16

Бренд: Fire-Lite Alarms Страницы: 48

Бренд: Junghans Страницы: 1

Бренд: Jung Страницы: 108

Бренд: SETRONIC VERONA Страницы: 4

Бренд: Gasmate Страницы: 20

Бренд: La Crosse Technology Страницы: 9

Бренд: Wander Oz Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды