VESDA VLC Скачать руководство пользователя | Manualshive

Страница: 18 / 58

background image

VESDA Maintenance Guide

VESDA

12

www.xtralis.com

Capillaries

Capillaries can only be installed in environment classes 1 to 4 (refer to Appendix B on page 49). Though not a
requirement for environment classes 1 & 2, cleaning of capillary tubes in moderately dirty areas (environment
classes 3 & 4) should follow the instructions below:

1. Ensure that detectors are isolated from the monitoring panel and fire suppression systems.
2. Notify the relevant authorities that work is being performed.
3. Check and record the current airflow for before and after comparison.
4. Disconnect the detector power supply.
5. Remove all pipes from the detector inlet(s) and exhausts then cover them to ensure that no further dust

can enter the detector.

6. Remove the capillary tubes from the sampling pipe and unscrew the sampling end pieces, if applicable.
7. Clean out the capillary tubes and sampling end pieces with a vacuum cleaner or compressed air source.
8. Visually check that each part has a clear air path.
9. Reassemble the sampling end pieces, if applicable, and connect them to the capillary tubes.

10. Reconnect the capillary tubes to the sampling pipe network, ensuring that there are no kinks. If the

sampling pipe network is also to be flushed, do not reconnect the capillary tubes until this has occurred.

11. Compare the before and after flow rates. Ideally, the flow should be close to 100% for each used pipe. If

this is not the case, the pipe network and detector may need closer inspection.

12. Once the system has been serviced, cleaned, tested and is operating fault-free, return it to its normal

operating mode.

HASP (Heat Activated Sampling point)

1. Visually inspect the HASP heat responsive element is free from dust, corrosion, paint, insects and other

foreign material

2. Visually inspect for poorly fitting or missing/damaged heat responsive element
3. Remove (unscrew) the HASP from the mounting base and conduct a smoke transport time test
4. Visually check for obstructions surrounding the HASP likely to impede heat of fire from reaching heat

responsive element.

Notes:

l

The HASP heat sensing element is NOT to be removed and reinserted for maintenance or any cleaning
activities.

l

Do not glue a poorly fitted or a removed heat sensing element to the HASP. Replace the HASP in its
entirety.

«
...
16
17
18
19
20
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: Radio Shack Страницы: 12

Бренд: TFA Страницы: 30

Бренд: HANNspree Страницы: 38

Бренд: Casio Страницы: 2

Бренд: Galeria Selection Страницы: 10

Бренд: Directed Electronics Страницы: 31

Бренд: Trevi Страницы: 9

Prestige APS-920

Бренд: Audiovox Страницы: 12

Platinum+ APS 687C

Бренд: Audiovox Страницы: 12

Бренд: The Fire Beam Страницы: 8

Бренд: Konig Страницы: 31

Бренд: Konig Страницы: 40

Бренд: Konifera Страницы: 144

Бренд: CrimeStopper Страницы: 18

CS-2000DPII TW2

Бренд: CrimeStopper Страницы: 24

CoolStart RS1905FM

Бренд: CrimeStopper Страницы: 32

FireCell FCX-174-001

Бренд: EMS Страницы: 2

Бренд: Eurochron Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды