VESDA VLC Скачать руководство пользователя

Страница: 4 / 58

VESDA Maintenance Guide

VESDA

www.xtralis.com

Document Conventions

The following typographic conventions are used in this document:

Convention Description

Bold

Used to denote:

emphasis.

Used for names of menus, menu options, toolbar buttons

Italics

Used to denote:

references to other parts of this document or other

documents. Used for the result of an action.

The following icons are used in this document:

Convention Description

Caution:

This icon is used to indicate that there is a danger to

equipment. The danger could be loss of data, physical damage, or
permanent corruption of configuration details.

Warning:

This icon is used to indicate that there is a danger of electric

shock. This may lead to death or permanent injury.

Warning:

This icon is used to indicate that there is a danger of inhaling

dangerous substances. This may lead to death or permanent injury.

Contact Us

UK and Europe

+44 1442 242 330

The Americas

+1 800 229 4434

Middle East

+962 6 588 5622

Asia

+86 10 56697101

Australia and New Zealand

+61 3 9936 7000

www.xtralis.com

Содержание VLC



























































Результаты поиска

Содержание VLC

Отзывы:

Похожие инструкции для VLC

Бренды по названию

Популярные бренды

VESDA VLC, Руководство по обслуживанию

Результаты поиска

Содержание VLC

Отзывы:

Похожие инструкции для VLC

Бренды по названию

Популярные бренды