VESDA VLC Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 58

background image

VESDA Maintenance Guide

VESDA

32

www.xtralis.com

8.4

VESDA VLI

8.4.1

Replacing the VESDA VLI Intelligent Filter

The VESDA VLI detector constantly monitors the difference between the flow of filtered and un-filtered air into
the manifold. The flow of filtered air decreases when compared to that of un-filtered air as dirt and other
particles accumulate in the Intelligent Filter. Although it is recommended to replace the Intelligent Filter every
two years, environmental conditions dictate the actual frequency of Intelligent Filter replacement.

The detector reports a fault condition that requires replacement of the Intelligent Filter when the flow of filtered
air falls below the minimum threshold when compared to the flow of un-filtered air.

Remove the Intelligent Filter

1. Set the detector to Standby mode.
2. Remove the front cover.
3. Unclip the Intelligent Filter (A) by pulling the locking lever outward (B).
4. Remove the Intelligent Filter.

A

B

Figure 8-19: Intelligent Filter Removal

Reinstall the Intelligent Filter

1. Position the Intelligent Filter inside the detector, aligning the locking tabs (A) to the slots (B).
2. Push the locking lever in the direction of arrow (C) until it clicks into the locked position and the Intelligent

Filter Present Switch (D) is actuated.

3. Execute the

Reset Intelligent Filter Life

command using Xtralis VSC.

Caution:

Do not reinstall a used filter.

C

4x

A

D

B

Figure 8-20: Intelligent Filter Installation

«
...
36
37
38
39
40
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: Omega Research & Development Страницы: 8

Бренд: aguilera electronica Страницы: 2

Бренд: ELRO Страницы: 2

Бренд: REV Ritter Страницы: 10

60.2009 Cone Wake-up Light

Бренд: TFA Страницы: 20

KIDS ALC-KROBOT

Бренд: Laser Страницы: 13

Бренд: AcuRite Страницы: 4

Бренд: Concept Smoke Screen Страницы: 8

Бренд: Kidde Страницы: 12

Бренд: Kidde Страницы: 6

Бренд: iHome Страницы: 14

Бренд: iHome Страницы: 14

Бренд: iHome Страницы: 16

Бренд: Naxa Страницы: 16

Бренд: La Crosse Страницы: 2

Бренд: Firex Страницы: 8

Бренд: Code Alarm Страницы: 11

Бренд: Code Alarm Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды