Vermont Castings CDVR33n Скачать руководство пользователя страница 27

Страница: 27 / 68

CDVSC7 & CDV7 Series Gas Fireplace

69D3011

FIReplaCe InSTallaTIon

noTe:

The gas line connection may be made using 1/"

rigid tubing or an approved flex connector. Since some

municipalities have additional local codes it is always best

to consult your local authorities and the current edition of

the National Fuel Gas Code ANSI.Z3.1, NFPA54. In

Canada CSA-B149 (1 or ) Installation Code.
A listed manual shutoff valve must be installed upstream of

the appliance. Union tee and plugged 1/8" NPT pressure

tapping point should be installed upstream of the appli-

ance.

Figure 41

IMpoRTanT:

Install main gas valve (equipment shutoff

valve) in an accessible location. The main gas valve is for

turning on or shutting off the gas to the fireplace.

Check your building codes for any special requirements for

locating equipment shutoff valve to fireplaces.

only persons licensed to work with gas

piping may make the necessary gas

connections to this appliance.

a manual shutoff valve must be installed

upstream of the appliance. union tee

and plugged 1/8” npT pressure tapping

point should be installed upstream of the

appliance.

Figure 41

use pipe joint sealant that is resistant to

liquid petroleum (lp) gas.

3" Minimum

FP1978
gas connection

Pipe Nipple

Cap

Figure 41 -

Gas Connection

Tee Joint

Approved Flexible

Gas Line

CSA Design-Certified Equipment Shutoff Valve

with 1/8" NPT Tap*

Sediment Trap/Drip Leg

natural Gas

From Gas Meter

(4.5" w.c. to 10.5" w.c. Pressure)

propane/lp

From External Regulator

(11" w.c. to 13" w.c. Pressure)

Apply pipe joint sealant lightly to male threads. This will

prevent excess sealant from going into pipe. Excess seal-

ant in pipe could result in clogged burner system valve.

We recommend that you install a sediment trap/drip leg in

supply line as shown in

Figure 41

. Locate sediment trap/

drip leg where it is within reach for cleaning. Install in piping

system between fuel supply and burner system. Locate

sediment trap/drip leg where trapped matter is not likely

to freeze. A sediment trap collects moisture and contami-

nants and keeps them from going into the burner system

gas controls. If sediment trap/drip leg is not installed or is

installed wrong, burner system may not run properly.

Содержание CDVR33n





































































Результаты поиска

Содержание CDVR33n

Отзывы:

Похожие инструкции для CDVR33n

Бренды по названию

Популярные бренды

Vermont Castings CDVR33n, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CDVR33n

Отзывы:

Похожие инструкции для CDVR33n

Бренды по названию

Популярные бренды