Vermont Castings CDVR33n Скачать руководство пользователя страница 19

Страница: 19 / 68

CDVSC7 & CDV7 Series Gas Fireplace

69D3011

VenTInG InSTallaTIon

FP2294
Side View Vent Termination
1/25/00 djt

Finish Wall

Vent

Termination

FP94

Figure 17 -

Side View of Final Unit Location

ReaR wall VenT InSTallaTIonS -

Flex VenT pIpe

Follow Steps 1 and on Page 19.

Step 3

Install the 4” (10 mm) flex vent pipe to the appliance col-

lars described in “General Information Assembling Vent

Pipes”, Page 1. If the installation requires a 45° angle,

grasp the vent pipe close to the appliance collar and bend

to 45°. DO NOT exceed 45°.

Figure 18

Install the 7” vent pipe in the same manner as Step .

noTe:

There must be a 1/” (13 mm) rise in a 1” (305

mm) length of flex vent.

Step 4

Assemble the flex vent to the collars on the termination as

you did on the appliance.

FP1473
corner flex install
4/04 djt

Termination

Flex Section

Appliance Collars

FP1473

Figure 18 -

Grasp the vent pipe close to the collar and

bend to 45° angle. do not exceed 45°.

FP1472
rise in length
4/04 djt

Rise

FP147

Figure 19 -

There must be a 1/2" rise per foot length

Top VenT SIDewall applICaTIon

noTe:

For all top vent installations where a 90° elbow

is the first pipe piece towards a sidewall termination (up

and out), an open-center ringed flue restrictor must be

installed onto the top edge of the firebox flue adapter. To

create this open-center re-

strictor, twist and break off

the center rib of the supplied

flue restrictor. The installed

part should appear similar

to that show n in

Figure 20.

Since it is very im-

portant that the

venting

system

maintain its balance

between the com-

bustion air intake and the flue gas exhaust, certain

limitations as to vent configurations apply and must

be strictly adhered to.

The Vent Graph, showing the relationship between verti-

cal and horizontal side wall venting, will help to determine

the various dimensions allowable.

Minimum clearance between vent pipes and combus-

tible materials is 3" (76 mm) on top, and 1" (25 mm) on

the bottom and sides unless otherwise noted.

When vent termination exits through foundations less

than 0” (508 mm) below siding outcrop, the vent pipe

must flush up with the siding.
It is best to locate the fireplace in such a way that mini-

mizes the number of offsets and horizontal vent length.
The horizontal vent run refers to the total length of vent

pipe from the flue collar of the fireplace (or the top of the

Transition Elbow) to the face of the outer wall.
Horizontal plane means no vertical rise exists on this por-

tion of the vent assembly.

when installing the appliance as a rear vent unit, the

90° or 45° Transition elbow attached directly to the

rear of the unit is noT InCluDeD in the following cri-

teria and calculations, and unless specifically men-

tioned should be ignored when calculating venting

layouts.

FP2303
CDV7 rear restrictor
3/09

Figure 20 -

Top Vent Vertical Sidewall

Restrictor

FP303

Содержание CDVR33n





































































Результаты поиска

Содержание CDVR33n

Отзывы:

Похожие инструкции для CDVR33n

Бренды по названию

Популярные бренды

Vermont Castings CDVR33n, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CDVR33n

Отзывы:

Похожие инструкции для CDVR33n

Бренды по названию

Популярные бренды