background image

CDVSC7 & CDV7 Series Gas Fireplace

69D3011

3

VenTInG InSTallaTIon     

Below GRaDe InSTallaTIon

When it is not possible to meet the required vent terminal 

clearances of 1” (305 mm) above grade level, a snor-

kel kit is recommended. It allows installation depth down 

to  7”  (178  mm)  below  grade  level. The  7”  (178  mm)  is 

measured from the center of the horizontal vent pipe as it 

penetrates through the wall.

ensure the sidewall venting clearances are observed. 

If venting system is installed below ground, we rec-

ommend  a  window  well  with  adequate  and  proper 

drainage to be installed around the termination area.

If installing a snorkel, a minimum 4” (610 mm) vertical 

rise is necessary. The maximum horizontal run with the 

4” vertical pipe is 36” (914 mm). This measurement is 

taken from the collar of the fireplace (or transition elbow) 

to the face of the exterior wall. See the Sidewall Venting 

Graph for extended horizontal run if the vertical exceeds 

4” (610 mm).
1.  Establish  vent  hole  through  the  wall. 

Page  22,  Figure 

26

.  Remove soil to a depth of approximately 16” (406 mm) 

below base of snorkel. Install drain pipe. Install window 

well  (not  supplied).  Refill  hole  with  1”  (305  mm)  of 

coarse gravel leaving a clearance of approximately 4” 

(10 mm) below snorkel. 

Figure 31

3.  Install vent system.

4.  Ensure a watertight seal is made around the vent pipe 

coming through the wall.

5.  Apply  high  temperature  sealant  caulking  (supplied) 

around the 4” and 7” snorkel collars.

6.  Slide the snorkel into the vent pipes and secure to the 

wall.

7.  Level the soil so as to maintain a 4” (10 mm) clearance 

below snorkel. 

Figure 31

BG402a
Top Vent
Below grade installation
1/26/00   djt

Firestop

7” Pipe

7TDVSNORK 

(Snorkel)

4” (10 mm) 

Clearance 

Min.

Window 

Well

Gravel

Drain

BG40a

Figure 31 - 

Below Grade Installation

*A minimum of 4” (610 mm) verti-

cal pipe must be installed when 

using the 7TDVSNORK Kit.

4” (610 mm) 

Minimum*

Screws

Foundation Wall

Do not back fill around snorkel.

a clearance of at least 4” must be maintained 

between the snorkel and the soil.

If  the  foundation  is  recessed,  use  recess  brackets  (not 

supplied) for securing lower portion of the snorkel. Fasten 

brackets to wall first, then secure to snorkel with self drill-

ing #8 x 1/ sheet metal screws. It will be necessary to 

extend vent pipes out as far as the protruding wall face. 

Figure 32

BG401

Snorkel

2/10/99   djt

Snorkel

Wall Screws

Foundation 

Recess

Watertight 

Seal Around 

PIpe

Sheet Metal Screws

BG401

Figure 32 - 

Snorkel installation, recessed foundation

VeRTICal ThRouGh-The-RooF applICa-

TIon

his gas fireplace has been approved for:

  Vertical installations up to 40’ (1 m) in height. Up to 

a 10’ (3 m) horizontal vent run can be installed within 

the vent system using a maximum of two 90° elbows. 

Figure 33

  Up to two 45° elbows may be used within the horizontal 

run. For each 45° elbow used on the horizontal plane, 

the  maximum  horizontal  length  must  be  reduced  by 

18” (450 mm). 

example:

 Maximum horizontal length:

 

No elbows 

= 10’ (3 m)

 

1 x 45° elbow  = 8.5’ (.6 m)

 

 x 45° elbows = 7’ (.1 m)

  A minimum of an 8’ (.5 m) vertical rise is required.

  Two sets of 45° elbow offsets may be used within the 

vertical sections. From 0 to a maximum of 8’ (.5 m) of 

vent pipe can be used between elbows. 

Figure 33

  7DVCS  supports  offsets. 

Figure  37.

  This  application 

will require that you first determine the roof pitch and 

use the appropriate starter kit. (Refer to Venting Com-

ponents List)

  The maximum angular variation allowed in the system 

is 70°. 

Figure 34

Содержание CDVR33n





































































Отзывы: