Vermont Castings CDVR33n Скачать руководство пользователя страница 26

Страница: 26 / 68

CDVSC7 & CDV7 Series Gas Fireplace

69D3011

FIReplaCe InSTallaTIon

CheCk GaS Type

Use proper gas type for the fireplace you are installing.

If you have conflicting gas type, do not install fireplace.

See dealer where you purchased the fireplace for proper

fireplace for your gas type or conversion kit.

InSTall GaS pIpInG To FIReplaCe /

BuRneR SySTeM loCaTIon

InSTallaTIon ITeMS neeDeD

Before installing fireplace and burner system, make sure

you have the items listed below.

•

External regulator

•

Piping (check local codes)

•

Equipment shutoff valve*

•

Test gauge connection*

•

Tee joint

•

Pipe wrench

•

Sediment trap (recommended)

•

Sealant (resistant to propane/LP gas)

(supplied by installer)

•

approved flexible gas line with gas connector (if

allowed by local codes — not provided)

* A CSA design-certified equipment shutoff valve with

1/8" NPT tap is an acceptable alternative to test

gauge connection. Purchase the CSA design-certified

equipment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply

an external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas

pressure to between 11 and 13 inches of water. If you do

not reduce incoming gas pressure, burner system regula-

tor damage could occur. Install external regulator with the

vent pointing down as shown in

Figure 40.

Pointing the

vent down protects it from freezing rain or sleet.

a qualified installer or service person must

connect appliance to gas supply. Follow all

local codes.

For propane/lp units, never connect

fireplace directly to the propane/lp supply.

This burner system requires an external

regulator (not supplied). Install the external

regulator between the burner system and

propane/lp supply.

FP1977
external regulator

Figure 40 -

External Regulator with Vent Pointing Down

(Propane/LP Only)

FP1977

External

Regulator

100 lb. (min)

Propane/LP

Supply Tank

Vent Pointing

Down

use only new black iron or steel pipe.

Internally tinned copper or copper tubing

can be used per national Fuel Code, Section

2.6.3, providing gas meets hydrogen sulfide

limits, and where permitted by local codes.

Gas piping system must be sized to provide

minimum inlet pressure (listed on data plate)

at the maximum flow rate (BTu/hr). undue

pressure loss will occur if the pipe is too

small.

When using copper of flex connectors use only fittings

approved for gas connections. The gas control inlet is

3/8" NPT.

Содержание CDVR33n





































































Результаты поиска

Содержание CDVR33n

Отзывы:

Похожие инструкции для CDVR33n

Бренды по названию

Популярные бренды

Vermont Castings CDVR33n, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CDVR33n

Отзывы:

Похожие инструкции для CDVR33n

Бренды по названию

Популярные бренды