Verlinde STAGEMAKER 100618073 страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 120

background image

1. Remove the plug of the power supply cable

from the power supply socket. Open the
cable gland. Remove the temporary power
supply cable by pulling it out through the
cable entry and the cable gland.

2. Place the main power supply cable through

the cable gland and the cable entry.
Connect the cable wires to the plug.
• To ensure the correct phase sequence,

pay attention to the order of the wires
when connecting them to the plug:
Connect the power control board (PCB)
connectors L1/L2/L3 with the phases
1/2/3 according to the correct phase
sequence.

• Connect the (yellow and green)

grounding wire with grounding (GND).

3. Slide the power supply cable assembly in

place. Connect the power supply plug to
the power supply socket.

4. Install the end cover.

Install the end cover and secure the fixation with the four screws. Tighten the screws to the
correct tightening torque.

OWNER’S MANUAL

This document and the information contained herein, is the exclusive property of Verlinde S.A.S and represents a non-
public, confidential and proprietary trade secret that may not be reproduced, disclosed to third parties, altered or
otherwise employed in any manner whatsoever without the express written consent of Verlinde S.A.S. Copyright 2020
© Verlinde S.A.S. All rights reserved.

6/2020

«
...
43
44
45
46
47
...
»

Содержание STAGEMAKER 100618073

























































































































Отзывы:

Нет отзывов

Похожие инструкции для STAGEMAKER 100618073

Бренд: GT Страницы: 8

Бренд: MW TOOLS Страницы: 10

Бренд: Knight Страницы: 138

Бренд: Tractel Страницы: 15

Бренд: Ribimex Страницы: 24

Ribitech PE100/200PT

Бренд: Ribimex Страницы: 28

Бренд: Yale Страницы: 14

Бренд: EINHELL Страницы: 130

Бренд: CRYSTEEL Страницы: 18

Бренд: EINHELL Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды