Verlinde STAGEMAKER 100618073 Скачать руководство пользователя | Manualshive

Страница: 44 / 120

background image

1

2

Figure 13. Cable gland positions of the chain hoist configuration B

1. Power supply

2. Control cable

4.8.2

Connecting the hoist to power supply

If the chain hoist is ordered without plugs, these instructions show you how to connect the chain
hoist to the power supply.

Before connecting the chain hoist to the main power supply network, check that

• rated voltages correspond to the main voltage. Check the voltages and frequencies that are

marked on the data plate of each product or component. For example, motors that are driven
by a frequency converter may have different values on their data plate than the values of the
chain hoist.

• power supply to the chain hoist is protected with fuses of correct size.

WARNING

ELECTRICAL SHOCK HAZARD
The chain hoist is delivered with a short power supply cable that is attached to the
power supply socket. The short power supply cable is only a temporary cable which is
not properly insulated. Connecting the temporary cable to the power supply can cause
an electric shock, which could lead to death, serious injury, or damage to the product.
Never connect the chain hoist to the power supply using the temporary power supply
cable. Remove the temporary power supply cable on the site and replace it with the
main power supply cable. Replace the temporary power supply cable before
connecting the chain hoist to the power supply.

4 INSTALLATION

This document and the information contained herein, is the exclusive property of Verlinde S.A.S and represents a non-
public, confidential and proprietary trade secret that may not be reproduced, disclosed to third parties, altered or
otherwise employed in any manner whatsoever without the express written consent of Verlinde S.A.S. Copyright 2020
© Verlinde S.A.S. All rights reserved.

6/2020

«
...
42
43
44
45
46
...
»

Содержание STAGEMAKER 100618073

























































































































Отзывы:

Нет отзывов

Похожие инструкции для STAGEMAKER 100618073

Бренд: Coffing Hoists Страницы: 36

scafor 408C Series

Бренд: Tractel Group Страницы: 16

Бренд: SATA Страницы: 64

Бренд: Tractel Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды