Verlinde STAGEMAKER 100618073 Скачать руководство пользователя | Manualshive

Страница: 89 / 120

background image

13. Plug in the brake cable (1).

14. Push in the control board.

15. Install the end cover on both the motor side and brake side.

For more information, see chapter Removing and installing the hoist covers.

16. Tighten the screws of the end covers to the correct tightening torque.

For more information, see chapter Tightening torques for the chain hoist.

17. Turn on the power to the chain hoist.

18. Check that the brake works normally.

1.

First test the brake without any load.

2.

Then test the brake with a dynamic test load of 110% (EUR) or 125% (US) of the rated
capacity. Size of the dynamic test load depends on the country regulations.

3.

In the European countries, test the brake also with a static test load of 125% of the
rated capacity.

7.4.5

Replacing the double brake

1. If a load is attached to the hook, remove it.

2. Disconnect the hoist from the main power supply network.

3. Remove the end cover on the brake side.

For more information, see chapter Removing and installing the hoist covers.

4. Check that the brake data of the

replacement brake matches with the data
of the original brake.
You can find the brake data in the sticker
that is attached to the brake.

OWNER’S MANUAL

This document and the information contained herein, is the exclusive property of Verlinde S.A.S and represents a non-
public, confidential and proprietary trade secret that may not be reproduced, disclosed to third parties, altered or
otherwise employed in any manner whatsoever without the express written consent of Verlinde S.A.S. Copyright 2020
© Verlinde S.A.S. All rights reserved.

6/2020

«
...
87
88
89
90
91
...
»

Содержание STAGEMAKER 100618073

























































































































Отзывы:

Нет отзывов

Похожие инструкции для STAGEMAKER 100618073

Бренд: little mule Страницы: 17

Бренд: Haklift Страницы: 17

Бренд: KITO Страницы: 37

Бренд: Columbus McKinnon Страницы: 10

Бренд: Columbus McKinnon Страницы: 11

Бренд: Columbus McKinnon Страницы: 11

Бренд: Columbus McKinnon Страницы: 26

CM LODESTAR A-H

Бренд: Columbus McKinnon Страницы: 32

Бренд: Columbus McKinnon Страницы: 32

CM Lodestar VS A

Бренд: Columbus McKinnon Страницы: 40

Бренд: Columbus McKinnon Страницы: 48

Бренд: Haklift Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды