Vega VEGABAR 86 Скачать руководство пользователя страница 11

Страница: 11 / 76

3 Product description

VEGABAR 86 • Secondary Device for electronic differential pressure

48048-EN-220817

Extreme process temperature jumps are also immediately detected

by the ø 28 mm measuring cell. The values are compared with that of

an additional temperature measurement on the ceramic base body.
Within only a few measuring cycles the intelligent sensor electronics

compensates unavoidable measurement deviations due to tempera-

ture shocks. Such shocks cause (depending on the set damping) only

slight, brief changes to the output signal.

Relative pressure

: the measuring cell is open to the atmosphere.

The ambient pressure is detected in the measuring cell and compen-

sated. It thus has no influence on the measured value.

Absolute pressure

: the measuring cell contains vacuum and is

encapsulated. The ambient pressure is not compensated and does

hence influence the measured value.

The following illustration shows the installation of the ceramic measur-

ing cell in the sensor as well as the sealing concept.

1
2
3

Fig. 4: Front-flush installation of the ceramic measuring cell with double seal

1 Housing, sensor

2 Measuring cell

3 Lateral seal for measuring cell

4 Additional, front seal for measuring cell

5 Diaphragm

3.3 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.
The packaging consists of environment-friendly, recyclable card-

board. For special versions, PE foam or PE foil is also used. Dispose

of the packaging material via specialised recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Pressure types

Seal concept

Packaging

Transport

Transport inspection

Содержание VEGABAR 86













































































Результаты поиска

Содержание VEGABAR 86

Отзывы:

Бренды по названию

Популярные бренды

Vega VEGABAR 86, Руководство по эксплуатации

Результаты поиска

Содержание VEGABAR 86

Отзывы:

Бренды по названию

Популярные бренды