Vega VEGABAR 86 Скачать руководство пользователя страница 10

Страница: 10 / 76

3 Product description

VEGABAR 86 • Secondary Device for electronic differential pressure

48048-EN-220817

Fig. 3: Example, electronic differential pressure for level measurement in pres

surized vessel
1 VEGABAR 86

2 VEGABAR 86, Secondary Device

The sensors are connected via a shielded four-wire cable. The meas-

ured value from the Secondary Device is read in and factored into the

calculations. Power supply and parameter adjustment are carried out

through the Primary Device.
You can find further information in chapter "

Combination Primary -

Secondary

" of this operating instructions.

The sensor element is the CERTEC

measuring cell with robust

ceramic diaphragm. The process pressure deflects the ceramic

diaphragm and causes a capacitance change in the measuring cell.

This capacitance change is converted into an electrical signal and

outputted as measured value via the output signal.
The measuring cell is available in two sizes:

•

CERTEC

(ø 28 mm) with transmitter ø 32 mm

•

Mini-CERTEC

(ø 17.5 mm) with transmitter ø 22 mm

A temperature sensor in the ceramic diaphragm of the CERTEC

on the ceramic base of the Mini-CERTEC

measuring cell detects the

actual process temperature. The temperature value is output via:

•

The display and adjustment module

Measuring system

Measuring system tem-

perature

Содержание VEGABAR 86













































































Результаты поиска

Содержание VEGABAR 86

Отзывы:

Бренды по названию

Популярные бренды

Vega VEGABAR 86, Руководство по эксплуатации

Результаты поиска

Содержание VEGABAR 86

Отзывы:

Бренды по названию

Популярные бренды