Figure 10 provides the full menu of features that can be set up on the system. Explanation of each
feature is provided in the section “CONTROLLER FEATURES”.
When setting up the VECTOR system via the LCD display, all the steps that have to be followed are
clearly provided via the display. It is only necessary to note the following:
?
To get into setup mode, press the (oblong) button for 3 seconds and follow the instructions
provided from there.
?
The buttons provided on the controller for navigating the system, are not marked because at each
step during the setup, the function given to each button is provided on the display.
?
When not in setup mode, ie normal mode, the (round) button is used as a TEST button for
operating the system. The up/down buttons are not used unless the diagnostic screens have been
selected to appear in normal mode, in which case these buttons allow switching from one screen
to the next.
For each feature a factory default setting has been programmed into the controller. Referred to as
an operating standard or PROFILE, these defaults have been determined to suit the requirements
of the specific region where the installation is being carried out. It is only necessary to change a
feature where the default does not suit the installation. When selecting any feature in the menu,
details of the current setting stored in the controller are displayed.
Refer to Table 1 on page 39 for the Schedule of Factory Defaults for each feature
Page 28
Menu Navigation Map
Menu Navigation Map
Page 29
Figure 10 Part A of “Menu Navigation Map”
Figure 9 View of Controller
SETTING LIMITS: 1
SAFETY: 2
AUTOCLOSE: 3
MODES OF OPERATION: 4
RUN PROFILE: 5
IR BEAMS: 6
Setup Wizard
MTRM Collision Force: 2.1
MTRS Collision Force: 2.2
Collision Count: 2.3
Autoclose Status: 3.1
Autoclose Time: 3.2
Autoclose Override Time: 3.3
Autoclose Advanced Options: 3.4
Operating Mode
Positive Close: 5.1
Leaf Delay: 5.2
Pre-Open Delay: 5.3
Pre-Close Delay: 5.4
Opening Speed: 5.5
Closing Speed: 5.6
Ramp up Distance: 5.7
Ramp down Distance: 5.8
Crawl Distance: 5.9
Torque Limit: 5.10
MTRM Opening Collision Force
MTRM Closing Collision Force
MTRS Opening Collision Force
MTRS Closing Collision Force
Autoclose on Open: 3.4.1
Autoclose on Partly Open: 3.4.2
Autoclose on Partly Closed: 3.4.3
Standard Mode
Condominium Mode
Reversing Mode
Positive Close Status: 5.1.1
Positive Close Type: 5.1.2
Positive Close Short Stop Value: 5.1.3
Positive Close Push Force: 5.1.4
Leaf Delay Status: 5.2.1
Leaf Delay Value: 5.2.2
Short Stop
MTRM Only
MTRS Only
MTRM & MTRS
PIRAC Control: 6.1
SAF Output Status: 6.2
IRBO = IRBC
IR Beam Alarms: 6.3
PIRAC Status: 6.1.1
Stop On Open: 6.1.2
Ambush Alarm: 6.3.1
Break in Alarm Status: 6.3.2
Stop On Open Status: 6.1.2.1
Stop Distance: 6.1.2.2
Ambush Alarm Status: 6.3.1.1
IRB Broken time: 6.3.1.2
S Sens1
S Sens2
M Sens1
M Sens2
Sens+
Sens-
Safe CLS
Safe OPN
Com
LCK/STP
TRG
PED
Com
FRX
LIT
Figure 10 provides the full menu of features that can be set up on the system. Explanation of each
feature is provided in the section “CONTROLLER FEATURES”.
When setting up the VECTOR system via the LCD display, all the steps that have to be followed are
clearly provided via the display. It is only necessary to note the following:
?
To get into setup mode, press the (oblong) button for 3 seconds and follow the instructions
provided from there.
?
The buttons provided on the controller for navigating the system, are not marked because at each
step during the setup, the function given to each button is provided on the display.
?
When not in setup mode, ie normal mode, the (round) button is used as a TEST button for
operating the system. The up/down buttons are not used unless the diagnostic screens have been
selected to appear in normal mode, in which case these buttons allow switching from one screen
to the next.
For each feature a factory default setting has been programmed into the controller. Referred to as
an operating standard or PROFILE, these defaults have been determined to suit the requirements
of the specific region where the installation is being carried out. It is only necessary to change a
feature where the default does not suit the installation. When selecting any feature in the menu,
details of the current setting stored in the controller are displayed.
Refer to Table 1 on page 39 for the Schedule of Factory Defaults for each feature
3
3
3
3
3
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
Exit
Go
Up/Dn
AutoClose
AutoClose
AutoClose
AutoClose
AutoClose
Menu Level
Menu Level
How to set up additional features
on the Vector Controller
How to set up additional features
on the Vector Controller
