manualshive.com logo in svg

VAT 653 Series, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
VAT 653 Series Скачать руководство пользователя страница 28

INSTALLATION 

Series 65

 

28/129 

Edition 2019-05-03 

963283EA

 

4.3.2 

Power and Sensor supply concepts 

This valve offers 3 alternative concepts to supply the sensor(s) with power. This depends on the sensor 
type and valve version that is used. This valve is available with an optional sensor power supply module 
(SPS) that converts 

±

15 VDC from the 24 VDC. 

 
Concepts: 
 

•

 

Ex24 VDC supplied to POWER connector is feedthrough to SENSOR connector to supply 24 
VDC sensors. Refer to chapter «Power and sensor connection (+24 VDC sensors)» for schematic and 
correct wiring.  

•

 

External 

±

15 VDC supplied to POWER connector is feedthrough to SENSOR connector to supply 

±

15 

VDC sensors. Refer to chapter «Power and sensor connection (

±

15 VDC sensors) without optional 

SPS module» for schematic and correct wiring. 

•

 

Ex24 VDC supplied to POWER connector is converted into 

±

15 VDC by the valve internal SPS 

and supplied to SENSOR connector to supply 

±

15 VDC sensors. Refer to chapter «Power and sensor 

connection (

±

15 VDC sensors) with optional SPS module» for schematic and correct wiring. 

 

 

 

This concept is only possible when SPS retrofit is installed. 

 
 
Valve versions: 
 

•

 

653. . - . . G . - . . . .  and 653 . . - . . H . - . . . .   

SPS module not included 

 

•

 

653 . . - . . A . - . . . .  and 653 . . - . . C . - . . . .   

SPS module included 

 

 

 

The SPS module can be retrofitted. Refer to chapter «Retrofit / replacement 
procedure» for instruction. 

 
 
 

 

 

Содержание 653 Series


































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды