CB-800
CB-1000
2.2 O
PERATIONAL
S
AFETY
The machine is designed to protect the operator as much as possible from any flying swept debris. Do not remove any passive or active
security features. You would expose yourself to the risk of injury.
During work it is necessary to follow safety regulations to avoid any injury to yourself or other persons present nearby and to avoid any
property damage. In the operating instructions, there these instructions are marked by the following warning symbol:
If you see this symbol in the operating instructions, carefully read the statement following after it, please!
This international safety symbol indicates important instructions concerning safety. When you see this symbol,
be cautious. There is a danger of accident to you or other individuals. Carefully read through the following
information.
Table 12: Symbols
2.2.1 S
AFETY
R
EGULATIONS
The machine operator must be over 18 years of age.
He is obliged
to familiarize himself/herself with the instructions for the
use of the machine and to be familiar with the general principles of occupational safety.
When working, use approved work aids and close-fitting clothing, sturdy footwear, work gloves, and safety goggles.
Due to the increased dustiness when sweeping up solid dirt, use a suitable dust mask or respirator or per
ČSN EN 149:2001+A1:2009
.
Due to the assumption of working with the machine in reduced visibility (snow, fog, in daytime without sufficient light) and
moving near public roads, wear clothing with reflective elements or use attachable reflective tapes etc.
Keep a safe distance from the machine given by the handlebar.
When working with the machine, all other people (
especially children
) and animals must stay outside the machine's work
area. The operator may only continue working after they reach a
safe
distance.
Before
every use of the machine,
check the tightness of its screw connections. Check, whether any part (especially the
working gear or its covering) is damaged or loose.
Identified defects must be
immediately eliminated
. Use only original
spare parts during repairs.
It is not allowed to use the machine in confined premises! Its exhaust gases contain toxic substances that can cause
unconsciousness and death.
Take extra care when handling the machine. When the engine is turned off, the exhaust silencer remains hot. When filling the
fuel make sure that no leak occurs and you do not spill the fuel over the engine parts. Otherwise, dry the affected parts or wait
until the petrol evaporates.
The machine features its rotating working tool. The maximum tip speed is
4 m.s
-1
. Therefore, ensure that any other persons
keep a safe distance when operating this machine (possibility of ejected solid objects flying away)!
It is forbidden to work with the machine on roads of all classes, except to drive perpendicularly over them only where permitted.
Only operate the machine in daylight.
The machine's
safe
slope accessibility is 10°. The maximum long-term tilt of the engine is 20° and short-term
one is 30°.
When using the machine on slippery surfaces (e.g. on the snow cover), always use quality winter footwear with an anti-skid
pattern. When the risk of falling down is imminent, do not hold on to the machine and do not try to stop it.
Do not drive on frozen lakes, ponds, watercourses or other water bodies. Ice may break through. Use extra caution when
working on slippery surfaces, especially if the slippery areas are covered with snow.
When the machine's travel is switched off, the machine may reverse sharply, due to the counter-rotation of its brushes.
Therefore, always keep a sufficient clear space behind you, free of obstacles.
Always turn OFF the engine and wait for the work tool to stop before performing any work in the close vicinity of the machine!
Always switch OFF the engine before leaving the machine!
It is forbidden to remove any protective devices and covers from the machines.
Any repairs, adjustments, lubrication, and cleaning of the machine must be carried out when the machine is at a standstill, and
its spark plug connector is disconnected.
When working with lubricants and cleaning the machine, observe the basic hygiene regulations and observe the environmental
protection regulations and laws.
Due to exceeding the recommended noise and vibration values, follow these instructions when working with the machine:
(a) Protect your hearing with ear muffs or earplugs. Request these aids from you distributor.
(b) After the maximum of 20 minutes of work with your machine, take a break for at least 10 minutes. During these breaks, the
respective operator must not be exposed to any other source of noise or vibrations.
40
Short term = up to one minute.
24
re
vi
ze
1
2/
20
21
