Vari Adela PRO BDR-720D, Перевод оригинальной инструкции

Страница: 24 / 68

BDR-720D Adela PRO
2.2 S
AFETY
The machine is designed to protect the operator as much as possible against any flying pieces of mowed growth. Do not remove any
passive or active security features. You would expose yourself to the risk of injury.
2.2.1 S
AFETY
S
YMBOLS IN THE
O
PERATING
I
NSTRUCTIONS
These instructions are marked in the operating instructions by the following warning symbol:

If you see this symbol in the operating instructions, carefully read the statement following after it, please!

This international safety symbol indicates important instructions concerning safety. When you see
this symbol, be alert to the possibility of your or other persons’ injury and carefully read the
following statement.
Table 14: Symbols
2.2.2 S
AFETY
P
ICTOGRAMS ON THE
M
ACHINE

The user is obliged to keep the pictograms on the machine in a readable state and, in case of any damage, ensure
their replacement.
Position: Number: Description:
Combined sticker on the
rear face of the engine
board
Fig. 5
1 Before using the machine, read through these Operating Instructions.
2
When servicing the machine, disconnect the wire from the ignition spark plug and remove the
battery from its holder.
3
It is forbidden to place your hands or feet into the operating area of the cutting tool – risk of
getting cut.
4
Risk of being hit by flying debris, cuttings, ejected items, etc. Other persons and animals -
keep a safe distance from the machine.
5 During work observe the maximum permissible slope for operation.
6 Use eye and ear protection when working.
Separate sticker on the
front cover
Fig. 9
- Tool turning direction arrow – Right (Clockwise)
Separate sticker on the
front cover
Fig. 10
-
Prohibited space for other persons and animals. The minimum safe distance from the
machine is 50 m .
Sticker on the control
lever on the right handlebar
Fig. 6
-
Switching on the cutting disc drive:
0 = cutting disk is not rotating 1 = safety lock ON 2 = cutting disc is rotating
Sticker on the control
lever on the right handlebar
Fig. 7
-
Machine travel start:
0 = machine is not moving 1 = machine is moving
Sticker on the control lever
on the left handlebar
Fig.
8
- Parking and service brake.
Table 15: Safety Pictograms
2.2.3 S
AFETY
R
EGULATIONS

The machine operator must be over 18 years of age. He is obliged to familiarize himself/herself with the instructions for the use
of the machine and to be familiar with the general principles of occupational safety.

During your work, use work aids approved according to ČSN EN 166 or ČSN EN 1731 (close-fitting clothes, sturdy shoes, work
gloves, and safety glasses). Keep a safe distance from the machine secured by the handlebar position.

Always make sure that no part (especially the working mechanism or its cover) is damaged or loose before using the machine.
Identified defects must be immediately eliminated. Use only original spare parts during repairs.

Before any use of the machine, check the tightening of its screws securing the blades in the upper disc and also the screws
securing the lower disc to the flange. If any blade is bent or excessively worn, you must always replace all the cutting disc
blades!

It is not allowed to use the machine in confined premises! Exhaust gases contain toxic substances that can cause
unconsciousness and death.

When filling the tanks with fuel, do not use open fire and do not refuel in the confined non-ventilated premises – danger of
explosion of fuel vapours.

When filling the fuel make sure that no leak occurs and you do not spill the fuel over the engine parts. If it be to the contrary, dry
the affected parts or wait until the petrol evaporates.
24
R
ev
iz
e
0
7
/2
0
2
1