background image

SECTION 6: MAINTENANCE

AIR N ARC

®

 300 SERIES ALL-IN-ONE POWER SYSTEM

®

PAGE - 88

090012-OP_r0

6.6.10  REBUILDING THE MINIMUM PRESSURE/

CHECK VALVE

Should a condition occur that requires the minimum
pressure/check valve to be serviced (see 

Section 7.2,

Troubleshooting Guide

), a repair kit is available. To

repair the minimum pressure/check valve, order
minimum pressure/check valve kit no. 270765. Refer to

Figure 6-14

, and the following procedure:

1.  With the machine off and the ignition key 

removed, open the hood panel.

2.  Locate the minimum pressure/check valve [

A

situated on the compressor unit’s control 
manifold, close to the coalescer element.

3.  Loosen and remove the lock nut [

B

] securing 

the grub screw [

C

] in position.

4.  Loosen the grub screw [

C

] to relieve any 

spring tension in the valve.

5.  Loosen and carefully remove the valve body 

[

D

], which holds the internal parts in place. 

The internal parts will be freed to drop out 
with the removal of the valve body. 

6.  Wipe internal surface of valve body [

D

] with a 

clean cloth.

7.  Consult 

Figure 6-14

, and re-assemble the kit 

by replacing all old parts with corresponding 
part provided in the kit.

8.  Once the kit parts (parts 

E

 through 

L

) have 

been situated in correct order into the valve 
body, replace the valve body back into the 
mounting position. Retighten body securely.

9.  Replace the grub screw [

C

] into position on 

valve body [

D

], and hand-tighten. Replace 

the lock nut [

B

] over the grub screw, and 

position it loosely over the grub screw.

6.6.10.1  SETTING THE MINIMUM PRESSURE 

VALVE

1.  Start the machine and allow it to assume idle 

speed.

TOOLS NEEDED

REPLACEMENT 

PART(S)

Clean Cloth

Minimum Pressure/

Check Valve 

Rebuild Kit No. 

270765

Adjustable Wrench

NOTE

Use all of the parts provided in the kit 

regardless of the replaceable part’s 

condition. 

Содержание 050518



















































































































































































































Отзывы: