Vanair 050518 Скачать руководство пользователя | Manualshive

Страница: 90 / 210

background image

SECTION 6: MAINTENANCE

AIR N ARC

®

300 SERIES ALL-IN-ONE POWER SYSTEM

®

PAGE - 72

090012-OP_r0

6.6.1 COMPRESSOR AIR FILTER

The compressor oil is the key to a long useful life of the
air compressor system. Dirt and other foreign matter can
be introduced into the compressor system through the air
intake. A clean air filter will ensure that the compressor is
protected. Consult

Section 6.3, Maintenance Schedule

Table

for routine compressor air filter inspection

intervals.

6.6.1.1 COMPRESSOR AIR FILTER CHECK

Consult

Figure 6-3

and the following procedure to check

the compressor air filter.

1. With the machine off and the ignition key

removed, open the hood panel.

2. Remove the two (2) wing nuts [

A

] from the air

filter cover [

B

] at the top of the compressor

unit.

3. Remove air filter element [

C

] from the air filter

mounting posts [

D

].

4. Inspect the air filter element for visible dirt,

debris, or damage.

NOTE:

To perform a

more thorough inspection of the compressor
air filter element, refer to

Section 6.6.1.2

.

If element is in adequate shape to continue using:

Re-tensioning the Air Compressor

Serpentine Drive Belt

6.6.15.1

page 93

Replacing the Air Compressor

Serpentine Drive Belt

6.6.15.2

page 95

Re-tensioning the Generator Ser-

pentine Drive Belt

6.6.15.3

page 97

Replacing the Generator Serpen-

tine Drive Belt

6.6.15.4

page 98

Re-tensioning the Engine

Hydraulic Pump Drive Belt

6.6.15.5

page 100

Replacing the Engine Hydraulic

Pump Drive Belt

6.6.15.6

page 101

TOOLS/ITEMS NEEDED

REPLACEMENT

PART(S)

Not Applicable

Not Applicable

System Component or

Part Group Task

Manual

Section

Location

WARNING

Relieve pressure from the compressor

system before removing any

components.

KEY

DESCRIPTION

A

WING NUT (x 2)

B

AIR FILTER MOUNTING
COVER

C

AIR FILTER HOUSING ELE-
MENT

D

MOUNTING POSTS (x 2)

Figure 6-3: Compressor Air Filter

A

C

B

D

NOTE

If element is compromised by dirt, holes,

tears, or the gaskets are worn, or it is in

unsatisfactory condition, then it will need

to be replaced.

«
...
88
89
90
91
92
...
»

Содержание 050518



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 050518

Бренд: Palmgren Страницы: 20

Бренд: WAGNER Страницы: 20

Бренд: Ofs Страницы: 3

Бренд: Parkside Страницы: 64

Бренд: Performance Tool Страницы: 4

ASye 636 Kinetik

Бренд: Fein Страницы: 77

Бренд: Rapid Страницы: 9

Бренд: Napa Страницы: 12

Бренд: Et system Страницы: 83

Бренд: Parkside Страницы: 100

Бренд: Lambda Electronics Страницы: 21

Бренд: RAMSET Страницы: 14

Бренд: Ulvac Страницы: 89

Бренд: FASANO TOOLS Страницы: 8

Бренд: Kett Страницы: 6

Бренд: Westfalia Страницы: 19

Hybrid Power ICT-IPS-DC12-BMM

Бренд: ICT Страницы: 60

Бренд: NEO TOOLS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды