Vallox Vallox TSK Multi 80 MV Скачать руководство пользователя страница 21

Страница: 21 / 108

SETUP WIZARD

EXPERT SETTINGS

1. Use the

Plus

and

Minus

buttons to turn the profile timer

function on or off. The options are:

• On

— When the timer is on, the

Boost

profile is used only for the

period specified in the timer.

• Off

— When the timer is off, the

Boost

profile is used until the

profile is changed, either manually or automatically by the week
clock.

2. Proceed to the next phase by selecting

Right arrow

3. Use the

Plus

and

Minus

buttons to set the profile timer duration

in minutes.

4. Select

5. Proceed to the settings of the next profile by selecting

Right

arrow

Fireplace profile

1. Use the

Plus

and

Minus

buttons to set the Fireplace profile

timer duration in minutes.

2. The

Fireplace

profile timer duration is now set.

3. Proceed to the next phase by selecting

Right arrow

4. Use the

Plus

and

Minus

buttons to set the

Fireplace

profile’s

supply air fan speed as a percentage of the maximum output
ratio.

TIP

It is recommended that a higher supply air fan speed be used in

the fireplace profile to create overpressure in the ventilation zone.

Reducing the extract air fan speed is not recommended.

5. The supply air fan speed of the

Fireplace

profile is now set.

6. Proceed to the next phase by selecting

Right arrow

7. Use the

Plus

and

Minus

buttons to set the extract air fan speed

of the

Fireplace profile

as a percentage of the maximum output

ratio.

8. The extract air fan speed of the

Fireplace

profile is now set.

9. Proceed to the next phase by selecting

Right arrow

10. Use the

Plus

and

Minus

buttons to turn the profile timer

function on or off. The options are:

• On

— When the timer is on, the

Fireplace

profile is used only for the

period specified by the timer.

• Off

— When the timer is off, the

Fireplace

profile is used until the

profile is changed, either manually or automatically by the Week
clock.

11. The profile timer function is now set.
12. Select

IMPORTANT

Do not turn the timer function off if there is no timer in the external

fireplace switch.

Finishing the setup

Once you have completed all phases of the setup, finish up the

setup as follows:

1. To change any of the set values, use the arrow buttons to

return to the desired line and then press

2. When you are satisfied with the settings, use the arrow buttons

to select

Start

and then press

TIP

You can browse the settings

of the Boost or the Fireplace

profile by using the Right arrow

button.

Содержание Vallox TSK Multi 80 MV










































































































Результаты поиска

Содержание Vallox TSK Multi 80 MV

Отзывы:

Похожие инструкции для Vallox TSK Multi 80 MV

Бренды по названию

Популярные бренды

Vallox Vallox TSK Multi 80 MV, Руководство пользователя

Результаты поиска

Содержание Vallox TSK Multi 80 MV

Отзывы:

Похожие инструкции для Vallox TSK Multi 80 MV

Бренды по названию

Популярные бренды