Vallox Vallox TSK Multi 80 MV Скачать руководство пользователя

Страница: 19 / 108

SETUP WIZARD

EXPERT SETTINGS

Basic fan settings

IMPORTANT

Adjust the air flows according to the values specified in the

ventilation plan. It is recommended that the air flows be

adjusted without having to choke the air flows at the valves.

This is the most energy-efficient set up.
First, set both values as close to the ideal value as possible

by looking at the supply and extract air fan curves. If the

ratio between the air flows is very high at first, the ventilation

unit may have to carry out extra defrosting cycles in sub-zero

temperatures, thus making adjustment of the air flows more

complicated. Check the air flows by measuring them at the

valves, and fine-tune the percentage values as required.

NOTE

If the outside air is extremely cold (below -10°C on an

aluminium cell or below -3°C on a plastic cell), the ventilation

unit may have to defrost the heat recovery cell. If this

happens, the

Defrosting

icon will be displayed on the control

panel. The air flows cannot be adjusted during defrosting.

Adjusting the supply and extract air flows

1. Use the

Plus

and

Minus

buttons to set the supply air fan

ratio as a percentage of the maximum output ratio. The
fan speed (1/min) will change accordingly.

2. Measure and adjust the supply air flows from the valves.
3. Press the

Right arrow button.

4. Use the

Plus

and

Minus

buttons to set the extract air fan

ratio as a percentage of the maximum output ratio. The
fan speed (1/min) will change accordingly. Measure and

adjust the extract air flows from the valves.

5. Select

. Supply and extract air flow settings are now

complete.

6. Record the set percentages in the measurement log.

Do not change the output ratio between the supply and

extract air fans once the settings are complete. The same

ratio is also used in the Away and Boost profiles.

TIP

You can browse the

Basic fan settings

by using the

Right

arrow

button.

NOTE

If the use of the ventilation unit has been started before air

flow adjustment, we recommend that the factory settings of

the ventilation unit be restored before adjustment is started

(see “Save and restore settings”). This ensure that the unit

settings are optimal for adjusting the air flows and that any

settings made during the adjustment are saved as setup

settings. Any later changes will be saved as user settings.

Both the setup and user settings can be restored later even

if the settings had been modified later.

IMPORTANT

The supply and extract air

settings have been completed

by a specialist during setup

of the ventilation unit. These

settings should be changed

only when the ventilation

unit is reconfigured, and not

at any other time. Changing

the ventilation settings so

that overpressure is created

can result in damage to the

structures of the building.

Содержание Vallox TSK Multi 80 MV










































































































Результаты поиска

Содержание Vallox TSK Multi 80 MV

Отзывы:

Похожие инструкции для Vallox TSK Multi 80 MV

Бренды по названию

Популярные бренды

Vallox Vallox TSK Multi 80 MV, Руководство пользователя

Результаты поиска

Содержание Vallox TSK Multi 80 MV

Отзывы:

Похожие инструкции для Vallox TSK Multi 80 MV

Бренды по названию

Популярные бренды