manualshive.com logo in svg

Val Controls IDC24-A, Руководство пользователя

Поделиться
Скачать
Val Controls IDC24-A Скачать руководство пользователя страница 71

 
 

 

DID-UM-002 

Val Controls A/S 

•

 Limfjordsvej 3 

•

 DK-6715 Esbjerg N 

•

 Tel. +45 7547 0600 

[email protected] 

•

 www.valcontrols.com 

Revision: 10 

 

 

71/74 

No. 43 

Reference SOT start 

Description 
 

A reference

 

SOT was started. 

 

 

No. 44 

Reference SOT finished 

Description 
 

A reference

 

SOT finished 

 

 

No. 45 

SOT aborted by operator 

Description 
 

A SOT was aborted by the operator 

 

No. 46 

Reference SOT aborted by operator 

Description 
 

A reference SOT was aborted by the operator 
 

 

No. 51 

Operational  

Description 
 

The IDC was set in operational mode 
 

 

No. 52 

Fail position remote 

Description 
 

The IDC was set in fail position mode 
 

 

No. 57 

Set in local mode 

Description 
 

The IDC was set in local mode 

 

No. 58 

Set in remote mode 

Description 
 

The IDC was set in remote mode 

 

No. 61 

Auto calibration was started 

Description 
 

An auto calibration was started 
 

 

No. 62 

Auto calibration finished 

Description 
 

An auto calibration finished 

 

No. 63 

Auto calibration aborted 

Description 
 

An auto calibration was aborted 

 

Содержание IDC24-A











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды