manualshive.com logo in svg

Val Controls IDC24-A, Руководство пользователя

Поделиться
Скачать
Val Controls IDC24-A Скачать руководство пользователя страница 69

 
 

 

DID-UM-002 

Val Controls A/S 

•

 Limfjordsvej 3 

•

 DK-6715 Esbjerg N 

•

 Tel. +45 7547 0600 

[email protected] 

•

 www.valcontrols.com 

Revision: 10 

 

 

69/74 

10

 

Event log 

No. 1 

IDC power on 

Description 
 

The IDC is power on 

 

No. 2 

System error 

Description 
 

An error was logged in the system error log. 
 

Argument 

System error no. 

 

No. 3 

System error removed 

Description 
 

An error was removed from the system error log 

Argument 

System error no. 

 

No. 11 

ESD line was power off 

Description 
 

The ESD line was power off. This event is only applicable for IDCs with 
external power supply. 
 

 

No. 12 

ESD line was power on 

Description 
 

The ESD line was power on. This event is only applicable for IDCs with 
external power supply. 
 

 

No. 13 

ESD reset 

Description 
 

An ESD reset was issued. This event is only applicable for IDCs with external 
power supply. 
 

 

No. 21 

PST start 

Description 
 

A PST was started. 
 

 

No. 22 

PST finished 

Description 
 

A PST was finished 
 

 

No. 23 

Reference PST start 

Description 
 

A reference

 

PST was started. 

 

 

Содержание IDC24-A











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды